Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

A Reusable Superheterodyne Dual-Band Down-Conversion Mixer With Hybrid Linearity-Enhanced Technique for 5G Non-Contiguous Multiband NR

A 27 - 57 GHz Down-conversion Mixer with Bulk Injection Technique

A 24-to-30 GHz Ultra-High-Linearity Down-Conversion Mixer for 5G Applications Using a New Linearization Method

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

A Novel Reconfigurable Ultra-Broadband Millimeter-Wave Photonic Harmonic Down-Converter

A Gm-boosted and current peaking wideband merged LNA and mixer

A Compact 2-18Ghz Ultra-Wideband Frequency-conversion T/R Module Based on a 3D Heterogeneous Integrated Process

Ultra-Broadband Photonic Harmonic Mixer Based on Optical Comb Generation

A K-Band High-Gain and Low-Noise Folded CMOS Mixer Using Current-Reuse and Cross-Coupled Techniques

A 24‐ghz Active Up/down Bidirectional Mixer in 130‐nm RF CMOS

A LOW POWER, HIGH-LINEARITY CMOS DOWNCONVERSION FOLDED MIXER FOR 2.4GHz ISM BAND APPLICATIONS

A 900mhz High Linearity Low Power Down-Conversion Mixer

A 0.5–2.5 GHz Mixer First Receiver With 200 MHz RF Bandwidth and $+$18.5 dBm OB-IIP3 in 180 nm CMOS for 5G NR Band

A 30-60 GHz Broadband Low LO-Drive Down-Conversion Mixer with Active IF Balun in 65 nm CMOS Technology

A 10ghz 2.8db Gain Passive Mixer In 0.18um Cmos Technology

A 39-GHz down-conversion mixer with a compact and broadband transformer-based image-rejection filter in 65-nm CMOS

Low power, high linearity multi-mode downconversion mixer for SDR

A 1.9 GHz High Linearity CMOS Up-mixer

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

Modified Broadband Ruthroff-Type Transmission Line Transformer Balun for Isolation-Enhanced Passive Mixer Design

An 18–28 GHz dual-mode down-converter IC for 5G applications