Abstract:Lithium cobalt oxide (LCO) as a classic layered oxide cathode for lithium-ion batteries is limited by the cutoff voltage, which only delivers about half of the theoretical capacity (∼4.2 V, 140 mA h g–1). Recently, raising the cutoff voltage to 4.6 V has been considered to further improve its specific capacity. However, LCO suffers from serious phase transition of O3 to H1-3, which leads to dramatic volume change and loss of cobalt, finally resulting in rapid capacity decay. In this work, we introduce the NASICON-structured LiZr2(PO4)3 (LZP), an ion conductor for lithium ion, to modify the surface of LCO by a wet-chemical method. Such a surface modification improves lithium-ion diffusion between the interface of LCO and electrolyte and restrains the O3 to H1-3 phase transition. As a result, the optimized LCO with 1 wt % coating (denoted as %) demonstrates enhanced electrochemical performance in both half-cell and full-cell. To be specific, % delivers a high specific capacity of 161.3 mA h g–1 and increases the capacity retention from 37.8 to 75.1% within 100 cycles. Importantly, the full-cell assembled by % and artificial graphite can exhibit an outstanding energy density of 345.5 W h kg–1 (based on the total mass of cathode and anode).The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.2c00533.TEM images; elemental mapping results; charge/discharge curves; CV curves; evolution of interplanar crystal spacing; GITT curves of a single testing step; EIS patterns; XRD and SEM images; cyclic performance of SAG; rate performance; open-circuit voltage of full-cell; and comparison of electrochemical performances with other high-voltage LCO reported in the literature (PDF)This article has not yet been cited by other publications.

Lattice Engineering on Li 2 CO 3 ‐Based Sacrificial Cathode Prelithiation Agent for Improving the Energy Density of Li‐Ion Battery Full‐Cell

Lattice Engineering on Li2CO3-Based Sacrificial Cathode Prelithiation Agent for Improving the Energy Density of Li-Ion Battery Full-Cell

Implanting Transition Metal into Li2O‐Based Cathode Prelithiation Agent for High‐Energy‐Density and Long‐Life Li‐Ion Batteries

Mitigating Lattice Distortion of High-Voltage LiCoO2 via Core-Shell Structure Induced by Cationic Heterogeneous Co-Doping for Lithium-Ion Batteries

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Mechanochemically Robust LiCoO<sub>2</sub> with Ultrahigh Capacity and Prolonged Cyclability

Rich-Carbonyl Carbon Catalysis Facilitating the Li2CO3 Decomposition for Cathode Lithium Compensation Agent

NASICON-Structured LiZr2(PO4)3 Surface Modification Improves Ionic Conductivity and Structural Stability of LiCoO2 for a Stable 4.6 V Cathode.

Structure/Interface Coupling Effect for High‐Voltage LiCoO<sub>2</sub> Cathodes

Suppressed Lattice Oxygen Release Via Ni/Mn Doping from Spent LiNi0.5Mn0.3Co0.2O2 Toward High-Energy Layered-Oxide Cathodes.

Unlocking the Decomposition Limitations of the Li2C2O4 for Highly Efficient Cathode Preliathiations

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathodes

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO2 at 4.65 V

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

A compact interphase involving reversible redox couple stabilizes 4.6 V LiCoO2 cathode

Eliminating oxygen releasing of Li-rich layered cathodes by tuning the distribution of superlattice domain

Mechanochemically Robust LiCoO2 with Ultrahigh Capacity and Prolonged Cyclability

Channelization of cathode/electrolyte interphase to enhance the rate-capability of LiCoO2

From Metal to Cathode Material: in situ Formation of LiCoO2 with Enhanced Cycling Performance and Suppressed Phase Transition

NASICON-Structured LiZr 2 (PO 4 ) 3 Surface Modification Improves Ionic Conductivity and Structural Stability of LiCoO 2 for a Stable 4.6 V Cathode

High‐Entropy Surface Complex Stabilized LiCoO2 Cathode