Abstract:A new strategy; cation and anion dual gradient, is proposed and successfully constructed at the surface of LiCoO2 to minimize the highly oxidized Co4+ and O− species when charged to high potentials, which not only suppresses the relevant surface side reactions, but also affected the Li+ diffusion kinetics through the induced spinel‐like surface structure, making LiCoO2 exhibit excellent cycling stability and rate capability at the high cutoff voltage of 4.6 V, further validated in the 4.55 V pouch full cell (equivalent to 4.6 V vs Li/Li+).LiCoO2 (LCO) is the most successful cathode material for commercial lithium‐ion batteries. Cycling LCO to high potentials up to 4.5 V or even 4.6 V can significantly elevate the capacity but cause structural degradation due to the serious surface side reaction between the highly oxidized Co4+ and O− species with organic electrolytes. To tackle this concern, a new strategy, constructing cation and anion dual gradients at the surface of LCO (DG‐LCO), is proposed. Specifically, the electrochemically inactive cation and anion are selected to substitute Co3+ and O2− at the surface in a gradated manner, thus minimizing the highly oxidized Co4+ and O− species at high potentials and suppressing the induced surface side reactions. Unexpectedly, this dual gradient design leads to a spinel‐like surface structure coherently with bulk layered structure, which facilitates Li+ diffusion kinetics. Thus, DG‐LCO achieves high capacity and excellent cycling stability at 4.6 V (≈216 mA h g−1 at 0.1 C, a capacity retention of 88.6% after 100 cycles in 1.8 A h pouch full cell at 1 C), as well as improved rate capability (≈140 mA h g−1 at 5 C). These studies provide useful guidelines for future design of cathode materials with long lifespan and high rate capability.

Mechanochemically Robust LiCoO<sub>2</sub> with Ultrahigh Capacity and Prolonged Cyclability

Mechanochemically Robust LiCoO2 with Ultrahigh Capacity and Prolonged Cyclability

Surface Design with Cation and Anion Dual Gradient Stabilizes High-Voltage LiCoO<sub>2</sub>

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

Structure/Interface Coupling Effect for High‐Voltage LiCoO<sub>2</sub> Cathodes

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathodes

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

Co-gradient Li-rich cathode relieving the capacity decay in Lithium-ion batteries

<i>In</i><i>-situ</i> constructed protective bilayer enabling stable cycling of LiCoO<sub>2</sub> cathode at high-voltage

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathode

In-situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO2 Cathode at High-Voltage

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

High‐Entropy Surface Complex Stabilized LiCoO2 Cathode

Channelization of cathode/electrolyte interphase to enhance the rate-capability of LiCoO2

High-Entropy Surface Complex Stabilized LiCoO<sub>2</sub> Cathode

Ultra-thin and Mechanically Stable LiCoO2-Electrolyte Interphase Enabled by Mg2+ Involved Electrolyte

In Situ Induced Lattice‐Matched Interfacial Oxygen‐Passivation‐Layer Endowing Li‐Rich and Mn‐Based Cathodes with Ultralong Life

Suppressing Bulk Strain and Surface O2 Release in Li-Rich Cathodes by Just Tuning the Li Content

From Metal to Cathode Material: in situ Formation of LiCoO2 with Enhanced Cycling Performance and Suppressed Phase Transition

Interphase Modification of Li(Ni0.5Co0.2Mn0.3)O2 Based Lithium Battery Electrode Materials by Depolarized and Pre-Lithiation for High Capacity and Cycling Performance