Abstract:Lithium cobalt oxide (LCO) as a classic layered oxide cathode for lithium-ion batteries is limited by the cutoff voltage, which only delivers about half of the theoretical capacity (∼4.2 V, 140 mA h g–1). Recently, raising the cutoff voltage to 4.6 V has been considered to further improve its specific capacity. However, LCO suffers from serious phase transition of O3 to H1-3, which leads to dramatic volume change and loss of cobalt, finally resulting in rapid capacity decay. In this work, we introduce the NASICON-structured LiZr2(PO4)3 (LZP), an ion conductor for lithium ion, to modify the surface of LCO by a wet-chemical method. Such a surface modification improves lithium-ion diffusion between the interface of LCO and electrolyte and restrains the O3 to H1-3 phase transition. As a result, the optimized LCO with 1 wt % coating (denoted as %) demonstrates enhanced electrochemical performance in both half-cell and full-cell. To be specific, % delivers a high specific capacity of 161.3 mA h g–1 and increases the capacity retention from 37.8 to 75.1% within 100 cycles. Importantly, the full-cell assembled by % and artificial graphite can exhibit an outstanding energy density of 345.5 W h kg–1 (based on the total mass of cathode and anode).The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.2c00533.TEM images; elemental mapping results; charge/discharge curves; CV curves; evolution of interplanar crystal spacing; GITT curves of a single testing step; EIS patterns; XRD and SEM images; cyclic performance of SAG; rate performance; open-circuit voltage of full-cell; and comparison of electrochemical performances with other high-voltage LCO reported in the literature (PDF)This article has not yet been cited by other publications.

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO2 at 4.65 V

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Surface-interspersed Nanoparticles Induced Cathode-Electrolyte Interphase Enabling Stable Cycling of High-Voltage LiCoO2

Surface-interspersed nanoparticles induced cathode-electrolyte interphase enabling stable cycling of high-voltage LiCoO 2

Tuning Surface Chemistry to Reduce the Step-Like Degradation of LiCoO2 at 4.6 V

External-to-internal Synergistic Strategy to Enable Multi-Scale Stabilization of LiCoO2 at High-Voltage

A compact interphase involving reversible redox couple stabilizes 4.6 V LiCoO2 cathode

Tuning surface chemistry to reduce the step-like degradation of LiCoO<sub>2</sub> at 4.6 V

Tuning Surface Reconfiguration for Durable Cathode/Electrolyte Interphase of LiCoO2 at 45 °C

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

Organic Cathode Electrolyte Interphase Achieving 4.8 V LiCoO2

Channelization of cathode/electrolyte interphase to enhance the rate-capability of LiCoO2

Tuning Surface Rock‐Salt Layer As Effective O Capture for Enhanced Structure Durability of LiCoO2 at 4.65 V

NASICON-Structured LiZr2(PO4)3 Surface Modification Improves Ionic Conductivity and Structural Stability of LiCoO2 for a Stable 4.6 V Cathode.

In-situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO2 Cathode at High-Voltage

Tuning Surface Reconfiguration for Durable Cathode/Electrolyte Interphase of LiCoO<sub>2</sub> at 45 °C

<i>In</i><i>-situ</i> constructed protective bilayer enabling stable cycling of LiCoO<sub>2</sub> cathode at high-voltage

Stabilizing LiCoO<sub>2</sub> at 4.6 V by regulating anti-oxidative solvents

NASICON-Structured LiZr 2 (PO 4 ) 3 Surface Modification Improves Ionic Conductivity and Structural Stability of LiCoO 2 for a Stable 4.6 V Cathode

Tuning Interphase Chemistry to Stabilize High‐Voltage LiCoO2 Cathode Material Via Spinel Coating

A Hybrid Ionic And Electronic Conductive Coating Layer For Enhanced Electrochemical Performance Of 4.6 V Licoo2