Abstract:Although the rapid development of electrical energy storage devices has slowed down environmental pollution, their large-scale application has posed huge challenges to battery-related mineral resources; thus, extending the lifespan of high-voltage lithium cobalt oxide (LCO) is of great importance. Surface oxide coating is considered as the most common low-cost modification method for addressing unstable cycling performance. However, studies have shown that the oxide layer would further react with an electrolyte, while the investigation on the corresponding component evolution is lacking. Herein, a typical example utilizing the above reaction to realize surface reconstruction is presented. Applying atomic layer deposition (ALD), originally, an ultrathin Al2O3 layer is coated on the LCO surface; however, this coating layer has undergone reconstruction after reacting with electrolyte decomposition products during the cycling. Compared with simple coating, the in situ formed Li3AlF6 layer has a tighter binding to the LCO surface while possessing good Li+ conductivity and electrochemical stability. In addition, the unique properties of the ALD technology allow us to achieve ultrathin (1 nm) and conformal coating, which is beneficial for electronic conductivity and cycling stability. Furthermore, the surface phase transition layer stripping failure mechanism has first been revealed to explain the loss of Co and O, while the reconstructed Li3AlF6 effectively suppresses the surface stripping. Thus, excellent high-voltage performance has been realized (an 89% capacity retention after 1000 cycles at 4.5 V and an 88% capacity retention after 200 cycles at 4.6 V). This work casts a new understanding on the surface reconstruction of the oxide coating layer, which is also significant for other electrode materials' modification.

Collective Surface Enabling an Ultralong Life of LiCoO2 at High Voltage and Elevated Temperature

Off-Stoichiometry Induced Few-Nanometer Surface Layer for High-Performance Layered Cathode in Nonaqueous and Aqueous Electrolytes

Diffusion‐Optimized Long Lifespan 4.6 V LiCoO2: Homogenizing Cycled Bulk‐To‐Surface Li Concentration with Reduced Structure Stress

Multiple Surface Optimizations for a Highly Durable LiCoO2 beyond 4.6 V

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

Multiple Surface Optimizations for a Highly Durable LiCoO<sub>2</sub> beyond 4.6 V

Surface-interspersed nanoparticles induced cathode-electrolyte interphase enabling stable cycling of high-voltage LiCoO 2

In-situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO2 Cathode at High-Voltage

An in Situ Formed Surface Coating Layer Enabling LiCoO2 with Stable 4.6 V High‐Voltage Cycle Performances

Ultralong Lifespan for High-Voltage LiCoO2 Enabled by In Situ Reconstruction of an Atomic Layer Deposition Coating Layer

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Highly stable operation of LiCoO2 at cut-off ≥ 4.6 V enabled by synergistic structural and interfacial manipulation

<i>In</i><i>-situ</i> constructed protective bilayer enabling stable cycling of LiCoO<sub>2</sub> cathode at high-voltage

One‐Step Sintering Synthesis Achieving Multiple Structure Modulations for High‐Voltage LiCoO2

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO2 at 4.65 V

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

LiMgPO<sub>4</sub>-Coating-Induced Phosphate Shell and Bulk Mg-Doping Enables Stable Ultra-High-Voltage Cycling of LiCoO<sub>2</sub> Cathode

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

LiMgPO4‐Coating‐Induced Phosphate Shell and Bulk Mg‐Doping Enables Stable Ultra‐High‐Voltage Cycling of LiCoO2 Cathode

Stabilizing 4.6 V LiCoO2 via Surface‐to‐Bulk Titanium Modification

Enhanced cycle stability of LiCoO2 at high voltage by mixed conductive Li7.5La3Zr1.5Co0.5O12 coating