Abstract:A surface‐to‐bulk modification with Li2TiO3 coating and gradient Ti doping is demonstrated to solve the deterioration of LiCoO2 at high voltage. The synergetic modification enhances Li+ diffusion, facilitates the construction of high‐quality cathode/electrolyte interphase, reduces the phase transition from O3 to H1‐3 and Co3d/O2p band overlap, and restrains layer‐to‐spinel phase distortion, thus improving structural stability at 4.6 V. Elevating the charging cut‐off voltage is an effective strategy to increase the energy density of LiCoO2. However, unstable interfacial structures and unfavorable phase transitions in bulk are inevitably triggered during deep de‐lithiation at high voltage. Herein, an integrated surface‐to‐bulk Ti‐modification strategy is applied to LiCoO2, enabling uniform Li2TiO3 coating on the surface and gradient Ti‐doping toward the structural bulk. The resultant Ti‐modified LiCoO2 (T‐LCO) electrode can be stably cycled up to 4.6 V, providing a high‐rate capability of 137 mAh g−1 at 5C and a long‐life stability with 80.5% capacity retention after 400 cycles at 1C, far outperforming the unmodified LiCoO2 electrode with only 50.7% capacity retention. In situ X‐ray diffraction characterization and density functional theory calculation reveal that the synergistic modification of T‐LCO enhances Li+ diffusion, facilitates the construction of high‐quality cathode/electrolyte interphase, reduces the phase transition from O3 to H1‐3 and Co3d/O2p band overlap, and restrains layer‐to‐spinel phase distortion, thus improving structural stability at 4.6 V. This work presents a "two birds one step" strategy to enhance the cycling stability and achievable capacity of high‐voltage LiCoO2 for developing high energy density lithium‐ion batteries.

An in Situ Formed Surface Coating Layer Enabling LiCoO2 with Stable 4.6 V High‐Voltage Cycle Performances

Off-Stoichiometry Induced Few-Nanometer Surface Layer for High-Performance Layered Cathode in Nonaqueous and Aqueous Electrolytes

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Conformal Coating of a High-Voltage Spinel to Stabilize LiCoO2 at 4.6 V

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

In-situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO2 Cathode at High-Voltage

Stabilizing 4.6 V LiCoO2 via Surface‐to‐Bulk Titanium Modification

Collective Surface Enabling an Ultralong Life of LiCoO2 at High Voltage and Elevated Temperature

A Surface Modification Layer with Cobalt Aluminate Inhibits 4.6 V High-Voltage Phase Transition of LiCoO2

Pushing Lithium Cobalt Oxides to 4.7 V by Lattice‐Matched Interfacial Engineering

Lattice‐Matched Interfacial Modulation Based on Olivine Enamel‐Like Front‐Face Fabrication for High‐Voltage LiCoO2

Engineering the Surface of LiCoO2 Electrodes Using Atomic Layer Deposition for Stable High-Voltage Lithium Ion Batteries

Realizing long-term cycling stability and superior rate performance of 4.5 V–LiCoO2 by aluminum doped zinc oxide coating achieved by a simple wet-mixing method

Multiple Surface Optimizations for a Highly Durable LiCoO2 beyond 4.6 V

Enhanced cycle stability of LiCoO2 at high voltage by mixed conductive Li7.5La3Zr1.5Co0.5O12 coating

Surface-interspersed nanoparticles induced cathode-electrolyte interphase enabling stable cycling of high-voltage LiCoO 2

Simultaneously Constructing a TiO2–LiF Composite Coating Enhancing the Cycling Stability of LiCoO2 at 4.6 V High Voltage

Superior stable high‐voltage LiCoO2 enabled by modification with a layer of lithiated polyvinylidene fluoride‐derived LiF

<i>In</i><i>-situ</i> constructed protective bilayer enabling stable cycling of LiCoO<sub>2</sub> cathode at high-voltage

A surface modification layer with cobalt aluminate inhibits 4.6 V high-voltage phase transition of LiCoO 2

In-situ reconstructed surface/inner-structure synergistic design enabling 4.6 V LiCoO 2 cathode for all-solid-state thin-film battery