Abstract:A new strategy; cation and anion dual gradient, is proposed and successfully constructed at the surface of LiCoO2 to minimize the highly oxidized Co4+ and O− species when charged to high potentials, which not only suppresses the relevant surface side reactions, but also affected the Li+ diffusion kinetics through the induced spinel‐like surface structure, making LiCoO2 exhibit excellent cycling stability and rate capability at the high cutoff voltage of 4.6 V, further validated in the 4.55 V pouch full cell (equivalent to 4.6 V vs Li/Li+).LiCoO2 (LCO) is the most successful cathode material for commercial lithium‐ion batteries. Cycling LCO to high potentials up to 4.5 V or even 4.6 V can significantly elevate the capacity but cause structural degradation due to the serious surface side reaction between the highly oxidized Co4+ and O− species with organic electrolytes. To tackle this concern, a new strategy, constructing cation and anion dual gradients at the surface of LCO (DG‐LCO), is proposed. Specifically, the electrochemically inactive cation and anion are selected to substitute Co3+ and O2− at the surface in a gradated manner, thus minimizing the highly oxidized Co4+ and O− species at high potentials and suppressing the induced surface side reactions. Unexpectedly, this dual gradient design leads to a spinel‐like surface structure coherently with bulk layered structure, which facilitates Li+ diffusion kinetics. Thus, DG‐LCO achieves high capacity and excellent cycling stability at 4.6 V (≈216 mA h g−1 at 0.1 C, a capacity retention of 88.6% after 100 cycles in 1.8 A h pouch full cell at 1 C), as well as improved rate capability (≈140 mA h g−1 at 5 C). These studies provide useful guidelines for future design of cathode materials with long lifespan and high rate capability.

NASICON-Structured LiZr 2 (PO 4 ) 3 Surface Modification Improves Ionic Conductivity and Structural Stability of LiCoO 2 for a Stable 4.6 V Cathode

Off-Stoichiometry Induced Few-Nanometer Surface Layer for High-Performance Layered Cathode in Nonaqueous and Aqueous Electrolytes

Mixed Lithium Ion and Electron Conducting LiAlPO 3.93 F 1.07 -Coated LiCoO 2 Cathode with Improved Electrochemical Performance

Enhanced electrochemical performance of Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 cathode material coated with Li + -conductive Li 2 SiO 3 for lithium ion batteries

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO2 at 4.65 V

Channelization of cathode/electrolyte interphase to enhance the rate-capability of LiCoO2

Surface engineering of LiCoO2 by a multifunctional nanoshell for stable 4.6V electrochemical performance

Surface Design with Cation and Anion Dual Gradient Stabilizes High-Voltage LiCoO<sub>2</sub>

In Situ-Constructed Multifunctional Interface for High-Voltage 4.6 V LiCoO2

Superior stable high‐voltage LiCoO2 enabled by modification with a layer of lithiated polyvinylidene fluoride‐derived LiF

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

Lithium-Aluminum-Phosphate Coating Enables Stable 4.6 V Cycling Performance of LiCoO2 at Room Temperature and Beyond

Long‐Term Highly Stable High‐Voltage LiCoO2 Synthesized via a Solid Sulfur‐Assisted One‐Pot Approach

Stable Cycling of LiCoO2 at 4.55 V Enabled by Combined Mg Doping and Surface Coating of NASICON-type Electrolyte

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

Realizing long-term cycling stability and superior rate performance of 4.5 V–LiCoO2 by aluminum doped zinc oxide coating achieved by a simple wet-mixing method

Stabilizing 4.6 V LiCoO2 via Surface‐to‐Bulk Titanium Modification

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Enhanced Electrochemical Performance of Li1.2mn0.54ni0.13co0.13o2 Cathode with an Ionic Conductive Livo3 Coating Layer