Abstract:Composite ceramics of 0.7BaO center dot 0.3SrO center dot(I-gamma)TiO2 center dot gamma Nb2O5 (BSTN) with coexistence of barium strontium titanate, Ba1-xSrxTiO3 (BST), and strontium barium mobate, SrxBa1-xNb2O6 (SBN) phases were successfully prepared in situ by controlling excess components according to a specially designed formula of 0.7BaO center dot 0.3SrO center dot(1-gamma)TiO2 center dot gamma Nb2O5 and by using a traditional ceramic process. X-ray diffractometry (XRD), scanning electron microscopy (SEM) and energy dispersion spectrometer (EDS) were used to characterize the phase composition, morphology and the micro-area chemical composition of the composite ceramics. The results showed that the SBN tungsten bronze phase appeared and coexisted stably with the BST perovskite phase when the excess content of Nb2O5 was > 6mol%, whereas the BST perovsklite phase formed and coexisted stably with the SBN tungsten bronze phase when the excess content of TiO2 was > 5.3mol%. In the ease of the two phases being equivalent to each other in BSTN composite ceramics, Nb2O5 was hard to be resolved into the perovskite phase, however, a few of TiO2 was easy to be resolved in the tungsten bronze phase. The microstructure of the composite ceramics were consisted of two kinds of grains. The smaller polygonal grains were belonged to the BST phase, and the larger ones to the SBN phase. The coexistence of the two phases inhibited the growth of the BST crystal. The density of microstructure of the composite ceramic was higher than that of both the pure BST and SBN calcined at the same temperature for the same time.

Tuning the combustion process during reactive sintering of high-performance ceramics by employing solid solutions as reactants

In Situ Combustion Synthesis of TiB<sub>2</sub>-AIN Composites

Reaction Sintering of Machinable TiB2-BN-C Ceramics with In-Situ Formed h-BN Nanostructure

Quantitative analysis and comparison on densification kinetics and grain growth mechanisms using reactively and directly densified TiB 2 -SiC- h BN ceramics

Effects of Boron Content on the Microstructure and Properties of BxC-TiB2 (x=4.5, 6.5 or 8.5) Ceramic Composites by the Reactive Spark Plasma Sintering

A microstructural approach to the chemical reactions during the spark plasma sintering of novel TiC–BN ceramics

Reactive sintering behavior and enhanced densification of (Ti,Zr)B2–(Zr,Ti)C composites

In situ reaction and solid solution induced hardening in (Ti,Zr)B 2 ‐(Zr,Ti)C composites

Fabrication of (Zr,Ti)B2-ZrN-BN composites through reactive spark plasma sintering of ZrB2 and TiN

In situ Preparation of BST(Nb)/SBN(Ti) Composites

Densification and mechanical properties of boron carbide prepared via spark plasma sintering with cubic boron nitride as an additive

Toughening mechanism of B4C/TiB2 ceramic materials by in situ reaction via spark plasma sintering

Influence of TiB2 and CrB2 on densification, microstructure, and mechanical properties of ZrB2 ceramics

TiB Whisker and Nitrogen Solid‐Solution Synergistic‐Strengthened Titanium Matrix Composites by Ti–BN via Spark Plasma Sintering and Hot Extrusion

B4C‒TiB2 composite with modified microstructure and enhanced properties from optimal size coupling of raw powders

Microstructure evolution, enhanced hardness and toughness in the solid-solution ceramic composite by reaction pressureless sintering of ZrB2 and TiC powders

Pressureless solid-state sintering of SiC ceramics with BN and C additives

Densification and comprehensive properties of h-BN-based refractories with in-situ formation of Y3Al5O12

Effect of B2O3 Addition on Low-temperature Sintering Behavior and Properties of SiC/h-BN Multiphase Ceramics

Microstructure and mechanical properties of h-BN–SiC ceramic composites prepared by in situ combustion synthesis