Abstract:Ni-P alloy coatings with tunable phosphorus contents are electrodeposited at room temperature using choline chloride: ethylene glycol (1: 2 molar ratio) deep eutectic solvent and NiCl2 center dot 6H(2)O, NaH2PO2 center dot H2O as nickel and respectively phosphorous sources. Cyclic voltammetry shows that the presentence of H2PO2- in the ionic liquid based Ni plating bath promotes the initiation of Ni-P nucleation. Chronoamperometric results indicate that the electrodeposition of Ni and Ni-P alloys on a platinum electrode follows the mechanism of instantaneous nucleation and three-dimensional growth with diffusion-controlled. Surface morphology and chemical composition of the alloy coatings are significantly dependent on the molar ratio of H2PO2-/Ni2+ in the electrolyte. Moreover, deposition potential and time have a remarkable effect on the surface morphology of deposits. X-ray diffractometer analysis indicates that the structure of alloys converts from crystalline to amorphous structure as the phosphorus content in the coating increases. Potentiodynamic polarization measurements show that the alloy coating exhibits the nobler corrosion potential and the lower corrosion current density compared with the Ni coating. The more phosphorus content the Ni-P coating has, the more positive corrosion potential and the lower corrosion current density the coating exhibits. (C) 2012 The Electrochemical Society. [DOI: 10.1149/2.012211jes] All rights reserved.

Effect of nickel immersion pretreatment on the corrosion performance of electroless deposited Ni–P alloys on aluminum

Influence of pretreatments on physicochemical properties of Ni-P coatings electrodeposited on aluminum alloy

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

A Method for Electroless Nickel Plating on Aluminum Alloy Surface

Effect of electroless deposition on the corrosion resistance property for NdFeB permanent magnets with surface coating of Ni-P alloy

Optimization of the Electroplating Process for Amorphous Nickel- Phosphorus Alloy

Effects of Surfactants in an Electroless Nickel-Plating Bath on the Properties of Ni−P Alloy Deposits

Effects of Ligands on Electroless Ni–P Alloy Plating from Alkaline Citrate–ammonia Solution

Electroless Deposition of Ni-Co-P Deposit on NdFeB Permanent Magnets and Its Corrosion Resistance Property

CHEMICAL PLATING MECHANISM IN ACID BATHS AND FABRICATION OF Ni-P COATING WITH HIGH P CONTENT

Process for Nickel-Phosphorous Pulse Electroplating and Corrosion Resistance of the Alloy Coating

Effect of Zinc Immersion Pretreatment on the Electro-Deposition of Ni Onto AZ91D Magnesium Alloy

Preparation of Amorphous Nickel-Phosphorus Alloy Coating by Electroplating

A Microporous Channel Copper Immersion Layer Promotes the Rapid Ni-P Electroless Plating Process on Aluminum Alloys at Medium and Low Temperatures

Electrochemical Synthesis and Characterization of Ni–P Alloy Coatings from Eutectic–Based Ionic Liquid

Electrodeposition of High Corrosion Resistance Cu/Ni–P Coating on AZ91D Magnesium Alloy

Ni-P coatings electroplating - A review, Part I: Pure Ni-P alloy

Effects of NH4F on the deposition rate and buffering capability of electroless Ni–P plating solution

Aluminum Co-Deposition via DC Magnetron Sputtering for Enhanced Pitting Resistance of Copper–Nickel Alloys

Study on Properties of Electroless Plating Nickel-phosphorus Bright Alloy Coating

Analysis of the Causes of Differences between the Upper and Lower Surfaces of Electroless Ni–P Coating on LZ91 Magnesium–Lithium Alloy