Abstract:Lithium-rich layered oxides have attracted much attention due to their high discharge capacity (>250 mA h·g–1). However, lithium-rich layered cathodes suffer from poor rate capabilities and voltage decay, which seriously limit their practical application. Herein, a unique @spinel double-spinel shell heterostructure is designed and successfully synthesized via coprecipitation and high-temperature solid-phase methods. In particular, lithium-rich layered oxides show good rate capabilities and high capacity retention when the molar amount of cobalt acetate and manganese acetate is 5%. After 100 cycles at 0.2 C, a discharge capacity of 232 mA h g–1 and a capacity retention of 92.7% can be obtained. The superior electrochemical performance of the in situ-transformed Li-rich layered cathode can be attributed to the unique three-dimensional diffusion channels for Li ions of the surface spinel phase. Besides, the in situ-transformed LiCoMnO4 shell can also improve the structural stability of the Li-rich layered oxides by reducing the side reactions and protecting the material from being corroded by the electrolyte. This study provides a strategy for surface modification, which can effectively improve the electrochemical performance of Li-rich layered cathode materials with high performance.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01955.SEM image of the precursor Ni1/6Co1/6Mn4/6CO3 and the corresponding mapping spectrum; ex situ XRD spectra of the LLO and LSS-0.05 samples; EDS line scan of the selected area and the corresponding HTEM diagram of the LSS-0.05 sample; CV and dQ/dV curves of the first three cycles of the LLO, LSS-0.05, and LSS-0.1 samples; initial charge and discharge curves of LiCoMnO4, LSS-0.2, and LSS-0.4 samples; discharge curves of LLO, LSS-0.05, and LSS-0.1 samples at different rates and with different cycles; typical single titration curve of GITT measurements; equivalent circuit of half-cells; and EIS spectra of LLO, LSS-0.05, and LSS-0.1 samples in the initial cycle (PDF)This article has not yet been cited by other publications.

Spinel-stabilized layered LiCoO2 cathode by surface reconstruction strategy

Off-Stoichiometry Induced Few-Nanometer Surface Layer for High-Performance Layered Cathode in Nonaqueous and Aqueous Electrolytes

Surface Modification and Electrochemical Properties of Li-Rich Layered Cathode Materials for Lithium-Ion Batteries

In Situ Constructed Spinel Layer Stabilized Upcycled LiCoO2 for High Performance Lithium‐Ion Batteries

Surface spinel reconstruction to suppress detrimental phase transition for stable LiNi0.8Co0.1Mn0.1O2 cathodes

In-situ reconstructed surface/inner-structure synergistic design enabling 4.6 V LiCoO 2 cathode for all-solid-state thin-film battery

Surface Modification Improves Spinel LiCoO2 Li-Ion Battery Cathode Materials Grown by Low Temperature Solvothermal Flow Reaction

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

In-situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO2 Cathode at High-Voltage

Surface Design with Cation and Anion Dual Gradient Stabilizes High-Voltage LiCoO<sub>2</sub>

Suppressing Bulk Strain and Surface O2 Release in Li-Rich Cathodes by Just Tuning the Li Content

<i>In</i><i>-situ</i> constructed protective bilayer enabling stable cycling of LiCoO<sub>2</sub> cathode at high-voltage

Bulk and surface reconstructed Li-rich Mn-based cathode material for lithium ion batteries with eliminating irreversible capacity loss

Improving the Electrochemical Performance of a Lithium-Rich Layered Cathode with an In Situ Transformed Layered@Spinel@Spinel Heterostructure

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

From Metal to Cathode Material: in situ Formation of LiCoO2 with Enhanced Cycling Performance and Suppressed Phase Transition

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO2 at 4.65 V

Tuning Surface Chemistry to Reduce the Step-Like Degradation of LiCoO2 at 4.6 V

One‐Step Sintering Synthesis Achieving Multiple Structure Modulations for High‐Voltage LiCoO2