Abstract:This paper presents characterization and compensation of the thermal bias drift of a MEMS accelerometer whose effective stiffness is electrostatically tuned to a low value with the help of the single-sided parallel plates (SSPPs) capacitors. A temperature drift model for the proposed accelerometer is built and the temperature effect on the mechanical stiffness and the circuit gains is characterized. The characterization reveals that the variations of the feedforward coefficient including the mechanical stiffness and the readout gain due to the temperature change play a significant role in the bias drift of output of the proposed closed-loop accelerometer. On the other hand, the variations of both feedback gain and tuning gain as a function of temperature are one-order-of-magnitude less than that of the feedforward coefficient. To calibrate the feedforward coefficient, an excitation signal as a form of AC reference displacement is introduced to drive the proof mass and the readout response is demodulated to calibrate the variance of the feedforward coefficient correspondingly. An open-loop compensation scheme for the temperature-induced bias drift using the variance of the calibrated response is proposed accordingly. Alternatively, the calibrated response can be controlled to a preset value by a new proportion integral derivative (PID) controller by the adjustment of the SSPP tuning voltage. The output of the PID controller is used for the calibration of the introduced bias from the electrostatic tuning force. Therefore, a closed-loop compensation of the thermal bias drift is achieved by remaining the feedforward coefficient while eliminating the calibrated bias. Experiments under a temperature cooling process and different tuning voltages are carried out to verify two proposed compensation schemes. The temperature drift coefficients (TDCs) of both compensated outputs exhibit at least one-order-of-magnitude reduction in response to the temperature change. When the effective stiffness of the accelerometer is tuned to about 4.19 N m(-1), the TDC of the compensated output using the proposed open-loop or closed-loop compensation schemes is reduced to about 0.1136 or 0.0391 mg degrees C-1, respectively and meanwhile, the Allan bias instability is slightly increased to 48.63 or 56.14 mu g, respectively.

Consideration of Thermo-Vacuum Stability of a MEMS Gyroscope for Space Applications

Design of Temperature Control System of Pico-Satellite MEMS Gyroscope

Design and Test of MEMS Gyroscope Control System Based on LMSD

A 0.09°/h Bias-Instability MEMS Gyroscope Working with a Fixed Resonance Frequency

Characterization and Compensation of Thermal Bias Drift of a Stiffness-Tunable MEMS Accelerometer

A Sub-0.1°/H Bias-Instability MEMS Gyroscope Using Resonant Constant-Frequency Driving Technique

Identification and Suppression of Driving Force Misalignment Angle for a MEMS Gyroscope Using Parametric Excitation

An Improved Phase-Robust Configuration for Vibration Amplitude-Phase Extraction for Capacitive MEMS Gyroscopes

Bias Thermal Stability Improvement of MEMS Gyroscope with Quadrature Motion Correction and Temperature Self‐sensing Compensation

Research on Temperature Compensation Technology of Micro-Electro-Mechanical Systems Gyroscope in Strap-Down Inertial Measurement Unit

Analysis and Compensation of Bias Drift for a Micromachined Spinning-rotor Gyroscope with Electrostatic Suspension.

A Temperature Drift Suppression Method of Mode-Matched MEMS Gyroscope Based on a Combination of Mode Reversal and Multiple Regression

MEMS Gyroscope Temperature Compensation Based on Drive Mode Vibration Characteristic Control

Driving-force compensation to improve the bias thermal stability of MEMS gyroscopes

Research on temperature dependent characteristics and compensation methods for digital gyroscope

A Temperature Compensation Method For Micromachined Thermal Gas Gyroscope

Temperature Drift Compensation for Four-Mass Vibration MEMS Gyroscope Based on EMD and Hybrid Filtering Fusion Method

A Temperature Characteristic Research and Compensation Design for Micro-Machined Gyroscope

Temperature Drift Error Compensation for MEMS Gyroscopes Based on SVR

120 Ppm Quality Factor Thermal Stability from -40 ℃ to +60℃ of a Dual-Axis MEMS Gyroscope Based on Joule Effect Dynamic Control

Humidity Drift Modeling and Compensation of MEMS Gyroscope Based on IAWTD-CSVM-EEMD Algorithms