Abstract:Black polymer films with high thermal stability are highly desired in flexible electrical and electronic fields. Conventional black polymer films based on high-temperature resistant polymers and black inorganic dyes are usually suffered from the poor electrical and tensile properties. In the current work, a series of intrinsically black polyimide (BPI) films with International Commission on Illumination (CIE) Lab optical parameters close to zero and high thermal stability have been designed and prepared. For this purpose, an electron-rich aromatic diamine, 4,4′-iminodianiline (NDA), was copolymerized with 1,4-phenylenediamine (PDA) and 3,3′,4,4′-biphenyltetracarboxylic dianhydride (sBPDA) to afford a series of poly(amic acid) (PAA) solutions, which were then thermally dehydrated to provide the final BPI films at elevated temperatures up to 400 °C in air. The molar fraction of NDA in the total diamine monomers was 0 for BPI-0 (sBPDA-PDA), 10% for BPI-1, 20% for BPI-2, 30% for BPI-3, 40% for BPI-4, 50% for BPI-5, and 100% for BPI-6. For comparison, two referenced polyimide (PI) films, including PI-ref1 and PI-ref2, were prepared according to a similar procedure. The former was derived from pyromellitic dianhydride (PMDA) and 4,4′-oxydianiline (ODA) and the latter was from PMDA and NDA. The BPI films exhibited an increasing degree of blackness with the increasing contents of NDA units in the polymer films. For example, the BPI-6 (sBPDA-NDA) film exhibited the optical transmittance of 1.4% at a wavelength of 650 nm (T650), which was obviously lower than those of PI-ref1 (T650 = 74.6%) and PI-ref2 (T650 = 3.6%). In addition, the BPI-6 film showed the CIE Lab parameters of 0.39 for L*, 2.65 for a*, 0.66 for b*, and haze of 1.83, which was very close to the criterion of "pure blackness" for polymer films (L* = a* = b* = 0). At last, incorporation of the NDA units in the rigid-rod BPI-0 (BPDA-PDA) film slightly deteriorated the high-temperature dimensional stability of the derived BPI films. BPI-6 film showed a linear coefficient of thermal expansion (CTE) value of 34.8 × 10−6/K in the temperature range of 50 to 250 °C, which was higher than those of the BPI-0 (CTE = 12.3 × 10−6/K), PI-ref1 (CTE = 29.5 × 10−6/K), and PI-ref2 (CTE = 18.8 × 10−6/K) films. Nevertheless, the BPI films maintained good thermal stability with the 5% weight loss temperatures (T5%) higher than 590 °C, and the glass transition temperatures (Tg) higher than 340 °C.

High-performance black polyimide with improved solubility for flexible printed circuit boards

Design, synthesis, and properties of soluble intrinsic black polyimide bearing tetraphenylcyclopentadienone units

Synthesis and Characterization of Polyimide with High Blackness and Low Thermal Expansion by Introducing 3,6-bis(thiophen-2-yl)diketopyrrolopyrrole-Based Chromophores

Rational design of soluble intrinsic black polyimide containing tetraphenylcyclopentadienone-based chromophore

Preparation and Properties of Intrinsically Black Polyimide Films with CIE Lab Color Parameters Close to Zero and High Thermal Stability for Potential Applications in Flexible Printed Circuit Boards

Organosoluble thermoplastic polyimide with improved thermal stability and UV absorption for temporary bonding and debonding in ultra-thin chip package

Intrinsically Black Polyimide with Retained Insulation and Thermal Properties: A Black Anthraquinone Derivative Capable of Linear Copolymerization

Thermoplastic polyimide with good comprehensive performance based on carbazole groups and short flexible linkages

Polyhedral oligosilsesquioxane-modified boron nitride enhances the mechanical properties of polyimide nanocomposites

Enhanced performance of low-dielectric siloxane-polyimide copolymers: Synthesis and properties

High Performance Biomass-Based Polyimides for Flexible Electronic Applications

Polyimides with Low Dielectric Constant and Dissipation Factor at High Frequency Derived from Novel Aromatic Diamine with Bistrifluoromethyl Pendant Groups

Chemically crosslinked polyimide-POSS hybrid: A dielectric material with improved dimensional stability and dielectric properties

Preparation and characterization of organic soluble polyimides with low dielectric constant containing trifluoromethyl for optoelectronic application

High Optical Transparency, Low Dielectric Constant and Light Color of Organosoluble Fluorinated Polyimides Based on 10,10-Bis[4-(4-amino-3-trifluoromethylphenoxy)phenyl]-9(10h)-anthrone

Synthesis and properties of novel colorless and thermostable polyimides containing cross‐linkable bulky tetrafluorostyrol pendant group and organosoluble triphenylmethane backbone structure

Cardo polyimides with high Tg and transparency derived from bisphenol fluorenes and 1,4-bis(4-fluorophthalimide)cyclohexanes via aromatic nucleophilic substitution

Synthesis and properties of modified thermoplastic polyimide films with good dielectric properties at high frequency and enhanced thermal stability via incorporation of rigid ester and biphenyl structural units

Preparation and Properties of Low-Dielectric Polyimide Films Containing Tert-Butyl

Intrinsically Negative Photosensitive Polyimides with Enhanced High-Temperature Dimensional Stability and Optical Transparency for Advanced Optical Applications via Simultaneous Incorporation of Trifluoromethyl and Benzanilide Units: Preparation and Properties

Novel rigid semi-alicyclic dianhydride with large side groups for high performance colorless polyimides (CPIs)