Abstract:Upon free solidification of a deeply undercooled melt, the solute diffusion in both the interface and the bulk liquid is far from equilibrium, and the concentration and the fluid flow may also play an important role in the solidification. Thus, under such conditions, assumptions about local equilibrium, ideal dilute solution solidification and solidification free of fluid flow can no longer be valid. In the present work, first, in order to reveal the concentration effect, we compared the results of the non-equilibrium dendrite growth models describing the solidification of dilute and non-dilute undercooled melts. It was found that under local non-equilibrium conditions, the predicted results of the non-dilute solution model and the dilute solution model are to a certain extent different from each other at the intermediate undercooling range. It was also found that the concentration effect could substantially decrease the relaxation effect. Second, we considered the effect of fluid flow on the rapid solidification of an undercooled melt. It was found that the fluid flow would affect not only the size of the dendrite tip radius, mainly at the small undercooling range, but also the dendrite growth velocity at the intermediate undercooling range. In particular, fluid flow makes the sizes of the dendrite tip radius at high undercooling close to those predicted by the dilute model. Thus, fluid flow could make the non-dilute solution exhibit dilute solution solidification behaviors. It was also found that fluid flow reduces the relaxation effect to some extent. Considering the fluid flow effect, we used an extended chemical superheating model to predict the dendrite remelting phenomenon of the non-dilute melt. The model predicted that the dendrite remelting phenomenon would abruptly disappear once the dendrite growth velocity exceeded the solute diffusion velocity in a bulk undercooled melt. Third, considering the fluid flow effect, we used the concept of equivalent undercooling and a recently developed physical model to calculate the stress accumulation during rapid solidification. The results of this new model could explain well the stress-induced dendrite breakup mechanism of grain refinement at high undercooling.

Investigation on Porosity Formation With Pressure Drop Between Dendrite Tip and Root During Pressurized Solidification of 30Cr15Mo1N Ingot

Evolution of Dendrite Structure and Shrinkage Porosity in 30Cr15Mo1N Ingot with Pouring Rate

Concentration and Fluid Flow Effects on Kinetics, Dendrite Remelting and Stress Accumulation Upon Rapid Solidification of Deeply Undercooled Alloys

Delving Deep into the Influence of Pressure on Columnar‐to‐Equiaxed Transition in High‐Nitrogen Steel Ingot by Thermodynamics and Kinetics

In situ observation and phase-field simulation on the influence of pressure rate on dendritic growth kinetics in the solidification of succinonitrile

Influence of Withdrawal Rate on the Porosity in a Third-Generation Ni-based Single Crystal Superalloy

Study on the Response of Dendritic Growth to Periodic Increase–decrease Pressure in Solidification Via in Situ Observation Using Succinonitrile

Simulating Study on the Shrinkage Cavity and Porosity of a Microalloyed Steel Ingot

Study on Dendritic Growth in Pressurized Solidification of Mg–Al Alloy Using Phase Field Simulation

In Situ Investigation of the Solidification of Al-20 Wt.% Zn Alloys Inoculated by Al-5Ti-1B

Effects of Pressure on Nitrogen Content and Solidification Structure during Pressurized Electroslag Remelting Process with Composite Electrode

Carbon Macrosegregation Pattern in 30Cr15Mo1N Ingot: Impact of Pouring Rate

Shrinkage Porosity Model for Steel Ingots with Reduction Deformation during Solidification

A STUDY OF LOCAL EFFECTS OF PORE AND CRITICAL REDUCTION FOR PORE CLOSURE IN HEAVY INGOTS

Effects of Solidification Shrinkage on Solute Segregation and Hot Cracking Sensitivity in Liquid Channel During Columnar Dendrite Growth

On the Porosity Induced by Externally Solidified Crystals in High-Pressure Die-Cast of Am60b Alloy and Its Effect on Crack Initiation and Propagation

Solidification behavior of undercooled Cu70Ni30 alloy melt

Effects of cooling rates on microporosity in DC casting Al-Li alloy

The characterization of porosity and its relationship with externally solidified crystal in a high-pressure die-cast AlSi10MnMg alloy via a laboratory CT technique

An integrated microporosity model of 3D X-ray micro-tomography and directional solidification simulations for Ni-based single crystal superalloys

The Influence of Insertion Depth of Inorganic Materials on Solidification Microstructure and Segregation of 2.5-ton 42CrMo Ingot