Abstract:Bands of interdendritic porosity and positive macrosegregation are commonly observed in pressure die castings, with previous studies demonstrating their close relation to dilatant shear bands in granular materials. Despite recent technological developments, the micromechanism governing dilatancy in the high-pressure die casting (HPDC) process for alloys between liquid and solid temperature regions is still not fully understood. To investigate the influence of fluid flow and the size of externally solidified crystals (ESCs) on the evolution of dilatant shear bands in HPDC, various filling velocities were trialled to produce HPDC samples of Al8SiMnMg alloys. This study demonstrates that crystal fragmentation is accompanied by a decrease in dilatational concentration, producing an indistinct shear band. Once crystal fragmentation stagnates, the enhanced deformation rate associated with a further increase in filling velocity (from 2.2 ms−1 to 4.6 ms−1) localizes dilatancy into a highly concentrated shear band. The optimal piston velocity is 3.6 ms-1, under which the average ESC size reaches the minimum, and the average yield stress and overall product of strength and elongation reach the maximum values of 144.6 MPa and 3.664 GPa%, respectively. By adopting the concept of force chain buckling in granular media, the evolution of dilatant shear bands in equiaxed solidifying alloys can be adequately explained based on further verification with DEM-type modeling in OpenFOAM. Three mechanisms for ESC-enhanced dilation are presented, elucidating previous reports relating the presence of ESCs to the subsequent shear band characteristics. By applying the physics of granular materials to equiaxed solidifying alloys, unique opportunities are presented for process optimization and microstructural modeling in HPDC.

On the Porosity Induced by Externally Solidified Crystals in High-Pressure Die-Cast of Am60b Alloy and Its Effect on Crack Initiation and Propagation

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

On the Tensile Failure Induced by Defect Band in High Pressure Die Casting of AM60B Magnesium Alloy

Effects of Runner Design and Pressurization on the Microstructure of a High-Pressure Die Cast Mg-3.0Nd-0.3Zn-0.6Zr Alloy

The characterization of porosity and its relationship with externally solidified crystal in a high-pressure die-cast AlSi10MnMg alloy via a laboratory CT technique

Characterization on the formation of porosity and tensile properties prediction in die casting Mg alloys

Effects of Process Parameters on Morphology and Distribution of Externally Solidified Crystals in Microstructure of Magnesium Alloy Die Castings

Correlation of 3D Defect-Band Morphologies and Mechanical Properties in High Pressure Die Casting Magnesium Alloy

Failure Behavior of High Pressure Die Casting AZ91D Magnesium Alloy

Influences of Initial Porosity, Stress Triaxiality and Lode Parameter on Plastic Deformation and Ductile Fracture

The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy

Study on the Externally Solidified Crystals in the Microstructure of Cold chamber High Pressure Die Casting Magnesium Alloy

Influence of Melt Flow in the Gating System on Microstructure and Mechanical Properties of High Pressure Die Casting AZ91D Magnesium Alloy

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

The Correlation Between Microstructure and Mechanical Properties of High-Pressure Die-Cast AM50 Alloy

The Effect of Slow Shot Speed and Casting Pressure on the 3D Microstructure of High Pressure Die Casting AE44 Magnesium Alloy

Influence of Different High Pressure Die Casting Processes on 3D Porosity Distribution of Mg-3.0Nd-0.3Zn-0.6Zr Alloy

The characterization of porosity and externally solidified crystals in a high pressure die casting hypoeutectic Al-Si alloy using a newly developed ceramic shot sleeve

Characterization of the Grain Structures in Vacuum-Assist High-Pressure Die Casting AM60B Alloy

The Evolution of Dilatant Shear Bands in High-Pressure Die Casting for Al-Si Alloys