Abstract:Megacasting is an innovative technique derived from high-pressure die-casting (HPDC). It offers the benefits of cost reduction and efficiency promotion by leveraging large-tonnage die-casting machines to produce multiple components into a single casting in one operation. However, the rapid filling and cooling process of HPDC inevitably gives rise to the potential problem of inconsistencies in mechanical properties throughout thin-walled megacastings, which limits their performance. To gain deeper insight into the issue, this study explores the mechanical properties and fracture mechanism of samples extracted from various regions within a megacasting. According to the distance from the gate, the concept of cold region and hot region for the megacasting is innovatively proposed. Tensile testing revealed that the mechanical properties of the castings exhibit variation in different regions, particularly in terms of elongation. The fracture surface of the cold region displays fluctuation due to the abundance of shrinkage defects present. Contrastingly, samples from the hot region feature relatively flat surfaces and tend to fracture due to defects like cold flakes and shrinkage in the skin layer. Furthermore, the empirical model for the area fraction of defects and ductility is developed. Three different fitting models are compared and the results show that the logarithmic model exhibits the highest modeling accuracy ( ). In conclusion, this study can serve as a valuable reference for the design of megacastings and contribute to the advancement of megacasting technology.

The Correlation Between Microstructure and Mechanical Properties of High-Pressure Die-Cast AM50 Alloy

Macro-micro Analysis of Mechanical Properties of Al0.6CoCrFeNi High-Entropy Alloy Particle-Reinforced Al-based Composites

In Situ Observation of Tensile Deformation of High-Pressure Die-Cast Specimens of AM50 Alloy

Correlation of 3D Defect-Band Morphologies and Mechanical Properties in High Pressure Die Casting Magnesium Alloy

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

Relationship Between Porosity Distribution and Mechanical Properties of Vacuum Die Casting AM50 Magnesium Alloy

Characteristics and distribution of microstructures in high pressure die cast alloys with X-ray microtomography: A review

The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

3-D Microstructural Distribution and Mechanical Analysis of HPDC Hypereutectic Al-Si Alloys via X-Ray Tomography

Characterization of the Grain Structures in Vacuum-Assist High-Pressure Die Casting AM60B Alloy

On the Porosity Induced by Externally Solidified Crystals in High-Pressure Die-Cast of Am60b Alloy and Its Effect on Crack Initiation and Propagation

Microstructure and mechanical properties of AM50 alloy according to thickness and forming condition of the products by a high pressure die-casting process

Characterization on the formation of porosity and tensile properties prediction in die casting Mg alloys

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

Microstructure and Mechanical Properties of High-Pressure Die Cast Pure Copper

On the Tensile Failure Induced by Defect Band in High Pressure Die Casting of AM60B Magnesium Alloy

Quantitative Analysis of 3D Pore Characteristics Effect on the Ductility of HPDC Al-10Si-0.3Mg Alloy through X-Ray Tomography

On the Deformation Behavior of Heterogeneous Microstructure and Its Effect on the Mechanical Properties of Die Cast AZ91D Magnesium Alloy

Mechanical Properties and Fracture Behaviors of a Non-heat-treated Alloy in Varied Regions Within a Megacasting