Abstract:Highlights • Multiple iron-rich phases in a HPDC AlSi10MnMg alloy is studied. • (P-IMC) I exhibits a lateral growth characteristic with a termination of {1 1 0}. • High density stacking fault exhibits in β phase. • (P-IMC) I and plate-shaped iron-rich phase exhibit a difference in mechanical behavior. The characterization of multiple iron-rich phases in high-pressure die-cast AlSi10MnMg alloy was studied. Attention was focused on the formation and fracture behavior of the primary iron-rich phase ((P-IMC) I ) formed in the shot sleeve and plate-shaped eutectic iron-rich phase in high-pressure die cast (HPDC) AlSi10MnMg alloy. Results show that multiple types of iron-rich phases with various morphologies, including primary iron-rich phases (polyhedral (P-IMC) I and (P-IMC) II ) and eutectic iron-rich phases (plate-shaped, net shape, and fish-bone shape), were found in HPDC AlSi10MnMg. Coarse (P-IMC) I formed in the shot sleeve were distributed in the interface between primary α-Al and binary Al-Si eutectic. Small size (P-IMC) II and various eutectic iron-rich phases formed in the die cavity and they were distributed in Al-Si binary eutectic. The primary iron-rich phases belonged to a simple cubic crystal structure with a lattice constant a = 1.265 nmand they exhibited a lateral growth characteristic with a termination of {110} surface along a (P-IMC) II [ 1 ̄ 1 2 ̄ ] direction. β phase was surrounded by δ phase and they coexisted in a plate-shaped iron-rich phase. High-density stacking fault in β phase and δ/β interface provided an excellent nucleation site for δ phase. From mechanical behavior, the stress concentration caused by eutectic iron-rich phases was far less than (P-IMC) I and it would not cause crack initiation along the eutectic cluster boundary. In addition, (P-IMC) I showed the worst deformation coordination with primary α-Al while the plate-shaped eutectic iron-rich phase exhibited similar deformation characteristics with silicon particles.

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

The characterization of Fe-rich phases in a high-pressure die cast hypoeutectic aluminum-silicon alloy

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

Crack Configuration Feature and Fracture Surface Difference for High Pressure Die Casting Hypereutectic Al-Si Alloys in High Cycle Fatigue

The characterization of porosity and its relationship with externally solidified crystal in a high-pressure die-cast AlSi10MnMg alloy via a laboratory CT technique

SEM-DIC characterization of the damage mechanism of an AlSi10Fe0.7 casting alloy on the microstructure scale

3-D Microstructural Distribution and Mechanical Analysis of HPDC Hypereutectic Al-Si Alloys via X-Ray Tomography

Analysis of Fractures and Microstructures on Different Injection Speeds in High-Pressure Die-Casting Magnesium Alloy

Unsteady-State Horizontal Solidification of an Al–Si–Cu–Fe Alloy: Relationship Between Thermal Parameters and Microstructure with Mechanical Properties/Fracture Feature

The Microstructure characteristics and fracture behavior of the polyhedral primary iron-rich phase and plate-shaped eutectic iron-rich phase in a high-pressure die-cast AlSi10MnMg alloy

The Correlation Between Microstructure and Mechanical Properties of High-Pressure Die-Cast AM50 Alloy

Fracture Behaviors of A390 Aluminum Cylinder Liner Alloys under Static Loading

Microstructure Evolution of Modified Die-Cast AlSi10MnMg Alloy During Solution Treatment and Its Effect on Mechanical Properties

Quantitative Analysis of 3D Pore Characteristics Effect on the Ductility of HPDC Al-10Si-0.3Mg Alloy through X-Ray Tomography

Investigation on microstructure heterogeneity of the HPDC AlSiMgMnCu alloy through 3D electron microscopy

On the Formation Mechanism of the Ring-Like Microstructure of High-Pressure Die-Cast A390 Alloy

Low cycle fatigue response and fracture mechanism in a novel Al-3.5Si-0.5Mg-0.4Cu casting alloy

New Technologies of Aluminum Castings. Effect of Microstructure on Fracture Toughness of Cast and Forged Aluminum Casting Alloys.

Effect of Slow Shot Speed on Externally Solidified Crystal, Porosity and Tensile Property in a Newly Developed High-Pressure Die-Cast Al-Si Alloy