Abstract:The effects of solution treatment on microstructural and mechanical properties of a novel Al-Zn-Mg alloy by microalloying with Sc and Zr were investigated by means of optical microscopy (OM), scanning electron microscopy (SEM), transition electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), differential scanning calorimeter (DSC), X-ray diffraction and tensile test, hardness measurement, respectively. The results show that solution treatment had a significantly effect on microstructural and mechanical properties. There exist lots of residual phases along rolling direction before solution treatment. With increasing solution temperature/time, the residual phases are dissolved into alpha-Al matrix gradually, and the number density of residual phases decreased. After solution treatment at 460 degrees C/60 min and aging treatment at 120 degrees C/24 h, the precipitated phase inside the grains are homogenously distributed eta' phase; the distribution of eta precipitates is discontinuous and coarsened on the grain boundary. With the increase of solution temperature(<= 470 degrees C) or solution time(<= 60 min), the precipitated phases inside the grains began to become more diffuse, and the grain boundary precipitated phases also gradually become smaller. When solution temperature further increased to 490 degrees C or solution time increased to 120 min, the precipitated phases within the grains and on the grain boundary began to coarsen. In addition, there also exists lots of fine Al-3(Sc, Zr) particles during aging treatment. Both tensile strength and hardness increase first and then decrease with increasing solution temperature or solution time. The optimum solution treatment is 470 degrees C/60 min. The ultimate tensile strength, yield strength and elongation of the aged studied alloys reached a maximum value, 581 MPa, 561 MPa, and 10.1%, respectively. (C) 2016 Elsevier B.V. All rights reserved.

Microstructure Evolution of Modified Die-Cast AlSi10MnMg Alloy During Solution Treatment and Its Effect on Mechanical Properties

Effect of Solutionising and Ageing on the Microstructure and Mechanical Properties of a High Strength Die-Cast Al–Mg–Zn–Si Alloy

Melt Superheating on the Microstructure and Mechanical Properties of Diecast Al-Mg-Si-Mn Alloy

Effects of Solution Treatment on Microstructure and Properties of Al-Mg-Si-Mn alloy

Effect of Solution Treatment on Microstructures, Properties and Fractography of Al-9.8Zn-2.37Mg-2.22Cu Aluminum Alloy

Synergistic Effects of Composition and Heat Treatment on Microstructure and Properties of Vacuum Die Cast Al-Si-Mg-Mn Alloys

Influence of Heat Treatment on the Evolution of Microstructure and Mechanical Properties of Mg-7Gd-5Y-0.6Zn-0.8Zr Magnesium Alloy

Mechanism of cryogenic, solid solution and aging compound heat treatment of die-cast Al alloys considering microstructure variation

Effects of Adding Trace Modification Elements and Heat Treatment on the Strength and Toughness of AlSi8Cu2MgMn Alloy

Effects of Solution Treatment on Microstructural and Mechanical Properties of Al–Zn–Mg Alloy by Microalloying with Sc and Zr

Effect of Solid-Solution Treatment on Microstructure and Hardness of Die-Casting Mg-9Al-1Zn-0.2Mn Alloy

Insight into the Partial Solutionisation of A High Pressure Die-Cast Al-Mg-Zn-Si Alloy for Mechanical Property Enhancement

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

Influence of the Solution and Artificial Aging Treatments on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Mg Alloys

Effect of the Solid Solution and Aging Treatment on the Mechanical Properties and Microstructure of a Novel Al-Mg-Si Alloy

Effect of heat treatments on microstructure and mechanical properties of sand cast Al–2Li–2Cu–0.5Mg–0.2Sc–0.2Zr alloy

Correlation of Solidification Microstructure Refining Scale, Mg Composition and Heat Treatment Conditions with Mechanical Properties in Al-7Si-Mg Cast Aluminum Alloys

Effects of Solution Treatment on the Microstructure, Tensile Properties, and Impact Toughness of an Al–5.0Mg–3.0Zn–1.0Cu Cast Alloy

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment