Abstract:Bands of interdendritic porosity and positive macrosegregation are commonly observed in pressure die castings, with previous studies demonstrating their close relation to dilatant shear bands in granular materials. Despite recent technological developments, the micromechanism governing dilatancy in the high-pressure die casting (HPDC) process for alloys between liquid and solid temperature regions is still not fully understood. To investigate the influence of fluid flow and the size of externally solidified crystals (ESCs) on the evolution of dilatant shear bands in HPDC, various filling velocities were trialled to produce HPDC samples of Al8SiMnMg alloys. This study demonstrates that crystal fragmentation is accompanied by a decrease in dilatational concentration, producing an indistinct shear band. Once crystal fragmentation stagnates, the enhanced deformation rate associated with a further increase in filling velocity (from 2.2 ms−1 to 4.6 ms−1) localizes dilatancy into a highly concentrated shear band. The optimal piston velocity is 3.6 ms-1, under which the average ESC size reaches the minimum, and the average yield stress and overall product of strength and elongation reach the maximum values of 144.6 MPa and 3.664 GPa%, respectively. By adopting the concept of force chain buckling in granular media, the evolution of dilatant shear bands in equiaxed solidifying alloys can be adequately explained based on further verification with DEM-type modeling in OpenFOAM. Three mechanisms for ESC-enhanced dilation are presented, elucidating previous reports relating the presence of ESCs to the subsequent shear band characteristics. By applying the physics of granular materials to equiaxed solidifying alloys, unique opportunities are presented for process optimization and microstructural modeling in HPDC.

The characterization of porosity and its relationship with externally solidified crystal in a high-pressure die-cast AlSi10MnMg alloy via a laboratory CT technique

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

The characterization of porosity and externally solidified crystals in a high pressure die casting hypoeutectic Al-Si alloy using a newly developed ceramic shot sleeve

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

On the Porosity Induced by Externally Solidified Crystals in High-Pressure Die-Cast of Am60b Alloy and Its Effect on Crack Initiation and Propagation

Characterization on the formation of porosity and tensile properties prediction in die casting Mg alloys

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology

The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy

Effect of Slow Shot Speed on Externally Solidified Crystal, Porosity and Tensile Property in a Newly Developed High-Pressure Die-Cast Al-Si Alloy

The effect of runner design and pressurization on the microstructure of high pressure die cast Mg-3.0Nd-0.3Zn-0.6Zr alloy

Using Micro-CT Scanning to Quantitative Characterize Porosity in High Pressure Die Castings and Semi-Solid Castings

Quantitative Analysis of 3D Pore Characteristics Effect on the Ductility of HPDC Al-10Si-0.3Mg Alloy through X-Ray Tomography

The characterization of Fe-rich phases in a high-pressure die cast hypoeutectic aluminum-silicon alloy

The Evolution of Dilatant Shear Bands in High-Pressure Die Casting for Al-Si Alloys

Three-dimensional visualization and quantification of microporosity in aluminum castings by X-ray micro-computed tomography

Correlation of 3D Defect-Band Morphologies and Mechanical Properties in High Pressure Die Casting Magnesium Alloy

The Effect of Slow Shot Speed and Casting Pressure on the 3D Microstructure of High Pressure Die Casting AE44 Magnesium Alloy

3D Characterization of Pores Expansion Behavior in High Pressure Die Castings During Heat Treatment

Influence of Different High Pressure Die Casting Processes on 3D Porosity Distribution of Mg-3.0Nd-0.3Zn-0.6Zr Alloy

Study on the Externally Solidified Crystals in the Microstructure of Cold chamber High Pressure Die Casting Magnesium Alloy