Abstract:The challenges commonly associated with conventional high-pressure die casting (HPDC) have led to increased interest in semi-solid metal (SSM) forming processes. In the present study, semi-solid slurries of A356 alloy prepared by the Swirled Enthalpy Equilibration Device (SEED) process were used for manufacturing components with complex shape by using a high pressure die casting (HPDC) machine. The segregation phenomenon and the effect of heat treatment on the microstructure evolution and mechanical properties were investigated. The results showed that the alloy consists of primary spherical α-Al grains, secondary solidified α-Al grains, eutectic Si, iron-rich intermetallic phases and low porosities. The microstructural investigations revealed that the eutectic Si particles underwent fragmentation, spheroidization and coarsening with increasing solution temperature. Furthermore, the solution treatment results in the dissolution of the π-Al 8 FeMg 3 Si 6 phase and the growth of the β-Al 5 FeSi phase. The hardening peaks at 170 o C could be obtained with ageing for 5 h. Due to both solution and precipitation strengthenings, the yield strength, ultimate tensile strength and hardness of A356 alloy after heat treatment increase significantly compared to those in the as-rheocast state: they reach 266 MPa, 343 MPa and 110 HV 0.2 , respectively. The analysis of fracture surfaces of rheo-HPDC samples in both the as-rheocast and the heat-treated states revealed a mixed mechanism of dimples and quasi-cleavage. The microstructure inside the part was found to be quasi-homogeneous while the segregation phenomenon in different zones of the part is affected by die geometry during the filling process. The results imply that the SEED-HPDC process has the potential to be industrialized by implementing appropriate heat treatments for producing complex components with good mechanical properties.

The characterization of porosity and externally solidified crystals in a high pressure die casting hypoeutectic Al-Si alloy using a newly developed ceramic shot sleeve

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

The characterization of porosity and its relationship with externally solidified crystal in a high-pressure die-cast AlSi10MnMg alloy via a laboratory CT technique

Study on the Externally Solidified Crystals in the Microstructure of Cold chamber High Pressure Die Casting Magnesium Alloy

Influence of Slow-Shot Speed on PSPs and Porosity of AlSi17Cu2.5 Alloy During High Pressure Die Casting

The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy

Enhanced mechanical properties and thermal conductivity of high-pressure die-cast AlMg6Si2MnZr alloy by controlling the externally solidified crystals

Effects of Process Parameters on Morphology and Distribution of Externally Solidified Crystals in Microstructure of Magnesium Alloy Die Castings

Effect of shot speeds on the microstructural framework and abnormal eutectic bands in a high pressure die casting hypoeutectic AlSi10MnMg alloy

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

The characterization of Fe-rich phases in a high-pressure die cast hypoeutectic aluminum-silicon alloy

Effect of Slow Shot Speed on Externally Solidified Crystal, Porosity and Tensile Property in a Newly Developed High-Pressure Die-Cast Al-Si Alloy

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology

Influence of Introducing Zr, Ti, Nb and Ce Elements on Externally Solidified Crystals and Mechanical Properties of High-Pressure Die-Casting Al–Si Alloy

On the Porosity Induced by Externally Solidified Crystals in High-Pressure Die-Cast of Am60b Alloy and Its Effect on Crack Initiation and Propagation

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

Effects of Shot Sleeve Pre-solidification on the Microstructure and Tensile Properties of High Pressure Die Cast AE44

Microstructure, segregation and mechanical properties of A356 alloy components fabricated by rheo-HPDC combined with the Swirled Enthalpy Equilibration Device (SEED) process

The Evolution of Dilatant Shear Bands in High-Pressure Die Casting for Al-Si Alloys

The Effect of Slow Shot Speed and Casting Pressure on the 3D Microstructure of High Pressure Die Casting AE44 Magnesium Alloy

Characterization on the formation of porosity and tensile properties prediction in die casting Mg alloys