Abstract:The 3D visualization of the porosity in high-pressure die casting (HPDC) Mg alloys AZ91D and Mg4Ce2Al0.5Mn (EA42) was investigated by X-ray computed tomography. It was demonstrated that the volumetric porosity at the near-gate location for alloy EA42 was significantly higher than that far from the gate location. This difference resulted from the low valid time during intensified casting pressure conditions. Specimens of alloy EA42 exhibited a narrow pore distribution in the side view (∼0.5 mm) compared to the wide distribution (∼1.8 mm) of alloy AZ91D, which was mainly attributed to the formation mechanism of the defect band. The formation of microporosity in the defect band of alloy EA42 was inhibited because of the significant latent heat released by a large amount of the Al11Ce3 phase segregated in the defect band during solidification. Additionally, an effective estimator (Z-Propagation) was introduced, which is proposed to predict the projected area fraction of the porosity (f) involved during tensile failure with better effectiveness compared with traditional methods based on the actual fractured surface. By coupling the Z-Propagation method with the critical local strain model, the logarithmic fracture strain and true fracture stress of the specimens were predicted within 3.03% and 1.65% of the absolute value of the average relative error (AARE), respectively.

Effects of Runner Design and Pressurization on the Microstructure of a High-Pressure Die Cast Mg-3.0Nd-0.3Zn-0.6Zr Alloy

Effect of Runner Design on the Externally Solidified Crystals in Vacuum Die-Cast Mg-3.0Nd-0.3Zn-0.6Zr Alloy

The Effect of Slow Shot Speed and Casting Pressure on the 3D Microstructure of High Pressure Die Casting AE44 Magnesium Alloy

The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy

Correlation of 3D Defect-Band Morphologies and Mechanical Properties in High Pressure Die Casting Magnesium Alloy

Influence of Different High Pressure Die Casting Processes on 3D Porosity Distribution of Mg-3.0Nd-0.3Zn-0.6Zr Alloy

Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties

On the Porosity Induced by Externally Solidified Crystals in High-Pressure Die-Cast of Am60b Alloy and Its Effect on Crack Initiation and Propagation

Effects of Process Parameters on Morphology and Distribution of Externally Solidified Crystals in Microstructure of Magnesium Alloy Die Castings

Effects of Shot Sleeve Pre-solidification on the Microstructure and Tensile Properties of High Pressure Die Cast AE44

Study on the Externally Solidified Crystals in the Microstructure of Cold chamber High Pressure Die Casting Magnesium Alloy

Influence of Melt Flow in the Gating System on Microstructure and Mechanical Properties of High Pressure Die Casting AZ91D Magnesium Alloy

Effect of Applied Pressure on Microstructures of Squeeze Cast Mg–15Gd–1Zn–0.4Zr Alloy

Effects of Casting Pressure Parameters on Porosities and Tensile Strength of a High Pressure Die Cast ADC12Z Alloy

Effect of shot speeds on the microstructural framework and abnormal eutectic bands in a high pressure die casting hypoeutectic AlSi10MnMg alloy

Influence of Introducing Zr, Ti, Nb and Ce Elements on Externally Solidified Crystals and Mechanical Properties of High-Pressure Die-Casting Al–Si Alloy

Analysis of Fractures and Microstructures on Different Injection Speeds in High-Pressure Die-Casting Magnesium Alloy

On the Tensile Failure Induced by Defect Band in High Pressure Die Casting of AM60B Magnesium Alloy

Effects of Pressure and Aging Treatment on Microstructures and Mechanical Properties of Rheo-Squeeze Casting Mg–3Nd–0.2Zn–0.4Zr Alloy

Characterization on the formation of porosity and tensile properties prediction in die casting Mg alloys

Effects of Casting Pressure on Microstructure and Mechanical Properties of Super Slow Speed Die Castings of ADC12 Aluminum Alloy