Abstract:The microstructure of single crystal Ni-based superalloys is virtually determined by both processing parameters of growth rate v and thermal gradient G ahead of the solidification front. Previous researches have established the relationship between dendrite spacings and G or v under supposing those parameters to be constant from beginning to end of solidification, resulting in the disaccord between the predicted and experimental results for actual blade, productions. Furthermore, previous experimental and theoretical works seldom involve the influence of processing parameter change on dendrite growth for multi-component industrial alloys. Therefore, investigation of directional solidified microstructure varying with processing parameter is the focus of present study. The influence of the withdrawing rate transition during directional solidification on the primary dendrite arm spacing (PDAS) and microsegregation for single crystal superalloy DD3 has been studied by liquid metal cooled (LMC) directional solidification method. A wide range of withdrawing rate variations from 50 to 600 mu m/s is allowable under G high to 250 K/cm. The results indicate that the average PDAS is remarkably dependent on the history of growth rate variation. The smaller PDASs of 56.5 and 86 mu m can be obtained under withdrawing rate transition from higher values of 600 and 300 mu m/s into 100 mu m/s, while they are kept being 111.5 mu m if withdrawing rate is 100 mu m/s all the time. In contrast. PDASs increase to 109 and 93 mu m under withdrawing rate transition from lower values of 50 and 100 mu m/s into 300 mu m/s, while they are kept being a small value of 70 mu m if growth rate is 300 mu m/s at beginning. These experimental results agree approximately with those from Hunt-Lu model, but the maximum to minimum ratio of PDASs at a given solidification parameter, i.e., lambda(max)(1)/lambda(min)(1), is proved to be more than 2. It is also shown that the dendrite microsegregation will be lessened with the decrease of PDASs at the same current solidification parameters.

Influence of Withdrawal Rate on the Porosity in a Third-Generation Ni-based Single Crystal Superalloy

Effect of Withdrawal Rate on the Microstructure and Mechanical Properties of a Novel Monocrystalline CoNi-based Superalloy

Effect of Withdrawal Rate on the Microsegregation, Thermophysical Properties and Spatial Orientation of a Ni3Al Based Single Crystal Superalloy

Effect of the Withdrawal Rate on the Microstructure and Creep Behavior of the Directionally Solidified Nickel-Based Superalloy

Influence of Withdrawal Rate on the Micro-Porosity of Super-Alloy DZ125 in Directional Solidification

Effect of Withdrawal Rate on Microstructure and Mechanical Properties of a Third Generation Nickel Based Single Crystal Superalloy

Influence of Withdrawal Rate on Last Stage Solidification Path of a Mo-rich Ni3Al Based Single Crystal Superalloy

Effect of solidification parameters on the microstructures of a single crystal Ni-based superalloy AM3

Effect of withdrawal rate on microstructure and lattice misfit of a Ni 3Al based single crystal superalloy

Influence of Withdrawal Rate on the Microstructure of Ni-base Single-Crystal Superalloys Containing Re and Ru

Effect of Withdrawal Rate on the Microstructure of Directionally Solidified NiAl–Cr(Mo) Hypereutectic Alloy

The Effects of Withdrawal and Melt Overheating Histories on the Microstructure of a Nickel-Based Single Crystal Superalloy

Effects Of Withdrawal Rate On The Microstructure Of Directionally Solidified Gh4720li Superalloys

Effect of Withdrawal Rate on the Microstructure of Directional Solidified Ni-43Ti-4Al-2Nb-2Hf Single Crystal Alloys

Effect of Withdrawal Rates on Microstructures and Room Temperature Fracture Toughness in a Directionally Solidified Nb–Ti–Cr–Si Based Alloy

Effect of Withdrawal Rate on the Microstructure of Directional Solidified Ti-47al-2cr-2nb-0.8b Alloys

Effect of Withdrawal Rate on Microstructure and Mechanical Properties of a Directionally Solidified NiAl-based Hypoeutectic Alloy Doped with Trace Hf and Ho

INFLUENCE OF WITHDRAWING RATE TRANSITION ON THE PRIMARY DENDRITE ARM SPACING AND MICROSEGREGATION OF DIRECTIONALLY SOLIDIFIED SINGLE CRYSTAL SUPERALLOY DD3

Effect of Withdrawal Rate on the Microstructure and Room Temperature Mechanical Properties of Directionally Solidified NiAl–Cr(Mo)–(Hf, Dy)–4Fe Alloy

Effect of Withdrawal Rate on Microstructure of Directionally Solidified Ni-45Ti-5Al Alloys

Yttrium Induced Formation of New Pores in an As-Cast Nickel-Based Single Crystal Superalloy