Abstract:After the converter steelmaking process, a considerable number of ferroalloys are needed to remove dissolved oxygen from the molten steel, but it also forms a lot of oxide inclusions that cannot be completely removed. At the same time, it increases the carbon emissions in the steel production process. After years of research, our team have developed a series of clean deoxidation technologies, including carbon deoxidation, hydrogen deoxidation, and waste plastic deoxidation of molten steel to address the aforementioned issues. In this study, thermodynamic calculations and laboratory experiments were employed to verify that carbon and hydrogen can reduce the total oxygen content in the molten steel melt to below 5 × 10 −6 and 10 × 10 −6 , respectively. An analysis of the deoxidation mechanisms and effects of polyethylene and polypropylene was also conducted. In addition, the applications of carbon deoxidation technology in different steels with the hot-state experiment and industrial production were discussed carefully. The carbon deoxidation experimental results of different steels were as follows: (1) the oxygen content of bearing steel was effectively controlled at 6.3 × 10 −6 and the inclusion number density was lowered by 74.73% compared to aluminum deoxidized bearing steel; (2) the oxygen content in gear steel was reduced to 7.7 × 10 −6 and a 54.49% reduction of inclusion number density was achieved with almost no inclusions larger than 5 μm from the average level of industry gear steels; (3) a total oxygen content of M2 high-speed steel was as low as 3.7 × 10 −6 . In industrial production practice, carbon deoxidation technique was applied in the final deoxidation stage for non-aluminum deoxidized bearing steel, and it yielded excellent results that the oxygen content was reduced to below 8 × 10 −6 and the oxide inclusions in the steel mainly consist of silicates, along with small amounts of spinel and calcium aluminate.

Investigation into Recycling of Iron Oxide Scale on H13 Steel by Low‐Temperature Carbothermal Reduction Method

Isothermal Reduction of Oxide Scale on Hot-Rolled, Low-Carbon Steel in 10 Pct H 2 -Ar

Identifying features in the structural and phase composition of the products of recycling of the scale of high-speed cutting steel by carbon thermal reduction

Effect of carbon on isothermal reduction of high-strength steel oxide scale in 30%H2–N2 atmosphere

A Laboratory Study of the Reduction of Iron Oxides by Hydrogen

High-efficiency reduction behavior for the oxide scale formed on hot-rolled steel in a mixed atmosphere of hydrogen and argon

Isothermal Reduction Behavior of Oxide Scale on the Surface of Hot‐Rolled Strip Steel Under Different Hydrogen Concentrations

Preparation of Direct Reduction Sponge Iron (DRI) Using Pyrite Cinder Containing Nonferrous Metals

Thermodynamic analysis and experimental verification of the direct reduction of iron ores with hydrogen at elevated temperature

Results of Hydrogen Reduction of Iron Ore Pellets at Different Temperatures

The Preparation of High-Purity Iron (99.987%) Employing a Process of Direct Reduction–Melting Separation–Slag Refining

Direct reduction of iron to facilitate net zero emissions in the steel industry: A review of research progress at different scales

Reduction of Oxide Scale with Hydrogen

Hydrogen-based direct reduction of iron oxide at 700°C: Heterogeneity at pellet and microstructure scales

Innovative Transformation and Valorisation of Red Mill Scale Waste into Ferroalloys: Carbothermic Reduction in the Presence of Alumina

Descaling Abilities of Two Low-Alloy High-Strength Steels Under Different Heating Processes

Effect Of Cold Rolling Before Hydrogen Reduction On Reduction Behavior And Morphologies Of Oxide Scale On Hot-Rolled Low-Carbon Steel

Investigation of (H2–H2O) partial pressure on the gas-based reduction of fine iron ore in mixed gases (H2–H2O–CO–CO2–N2)

New steelmaking process based on clean deoxidation technology

Influence of Reduction Temperatures on Reduction of FeO-Containing Slag by Agricultural Waste

Reduction of Iron‐Ore Pellets Using Different Gas Mixtures and Temperatures