Abstract:A site-specific xenon plasma focused ion beam preparation technique for microcantilever samples (1-20 µm width and 1:10 aspect ratio) is presented. The novelty of the methodology is the use of a chunk lift-out onto a clean silicon wafer to facilitate easy access of a low-cost probe type indenter which provides bending force measurement. The lift-out method allows sufficient room for the indenter and a line of sight for the electron beam to enable displacement measurement. An electroplated nanotwinned copper (NTC) was cut to a 3 × 3 × 25 µm microbeam and in situ mechanically tested using the developed technique. It demonstrated measured values of Youngs modulus of 78.7 ± 11 GPa and flow stress of 0.80 ± 0.05 GPa, which is within the ranges reported in the literature. LAY DESCRIPTION: In this paper a site specific method is present for making particularly small mechanical tests samples, of the order of 100th the size of a human hair. These small samples can then be used to determine the mechanical properties of the bulk material. Copper with a nano twinned grain structure is used as a test medium. Ion milling was used to cut the sample to shape and a micro probe was used for mechanical testing. Ion milling can cut away very small volumes of material as it accelerates ions at the surface of the sample, atomically machining the sample. Micro probes are a cost-effective small-scale load measurement devices, however, they require a large area for accessing the sample. The indenter requirements are a problem when making you samples with ion milling as ion millers are best at making small cuts. Our aim was to design a cutting strategy which reduces the amount of cutting required while allowing samples to be fabricated anywhere on the sample. We used a chunk lift out technique to remove a piece of material which is then welded to a wafer of silicon this gives sufficient space around the sample for ion milling and testing. The additional space allowed easy access for the probe. A 3 × 3 × 10 µm micro cantilever beam was cut out from copper, this beam was then bent. The force from bending and distance bent was measured and converted into Youngs modulus which is a measure of flexibility. The modulus value measured was comparable to the values reported in other papers.

Ion-Induced Bending with Applications for High-Resolution Electron Imaging of Nanometer-Sized Samples

Self-marked preparation of site-specific transmission electron microscope lamellae of nanodevices using focusing ion beam technique.

Focused-ion-beam stress introducing technology for micro/nano-fabrications

Focused ion beam preparation of microbeams for in situ mechanical analysis of electroplated nanotwinned copper with probe type indenters

Cryogenic Focused Ion Beam Enables Atomic-Resolution Imaging of Local Structures in Highly Sensitive Bulk Crystals and Devices

Nanoscale 3D tomography by in-flight fluorescence spectroscopy of atoms sputtered by a focused ion beam

The Trends of in Situ Focused Ion Beam Technology: Toward Preparing Transmission Electron Microscopy Lamella and Devices at the Atomic Scale

Modern Focused-Ion-Beam-Based Site-Specific Specimen Preparation for Atom Probe Tomography

In-Plane Liftout and Push-to-Pull for In Situ Mechanical Testing of Irradiated Inconel X-750

Focused Ion Beam Assisted Interface Detection for Fabricating Functional Plasmonic Nanostructures

In Situ Sputtering From the Micromanipulator to Enable Cryogenic Preparation of Specimens for Atom Probe Tomography by Focused-Ion Beam

Sample Preparation and Experimental Design for In Situ Multi-Beam Transmission Electron Microscopy Irradiation Experiments

Scalable Substrate Development for Aqueous Biological Samples for Atom Probe Tomography

Novel Method for the Preparation of Lamellas From Porous and Brittle Materials for In Situ TEM Heating/Biasing

Exploring the influence of focused ion beam processing and scanning electron microscopy imaging on solid-state electrolytes

Nanoscale coating on tip geometry by cryogenic focused ion beam deposition

Controlled Manipulation and Multiscale Modeling of Suspended Silicon Nanostructures under Site-Specific Ion Irradiation

Fabrication of Specimens for Atom Probe Tomography Using a Combined Gallium and Neon Focused Ion Beam Milling Approach

Optimizing site-specific specimen preparation for atom probe tomography by using hydrogen for visualizing radiation-induced damage

Site-specific femtosecond laser ablation: The pathway to high-throughput atom probe tomography characterization