Abstract:SnO2 has the advantages of excellent photostability and can be prepared at low-temperature below 200 ℃. It is regarded as one of the excellent materials for the electron transport layer, and widely used in efficient and stable planar heterojunction perovskite solar cells. In this work, the low-cost, dense and uniform SnO2 electron transport layer is prepared by spin coating at low temperature (150 ℃) for perovskite solar cells with a structure of FTO/SnO2/CH3NH3PbI3 (MAPbI3)/Spiro-OMeTAD/Au. The crystallization and photoelectric properties of SnO2 electron transport layers prepared at different concentrations (2.5%–10%) at 150 ℃, and the influences of SnO2 electron transport layers on the formation of perovskite films and the performances of perovskite solar cells are discussed. By analyzing the scanning electron microscope (SEM), ultraviolet-visible light absorption spectrum (UV-Vis) and transmission spectrum of the SnO2 film, it is found that the coverage and light transmittance of the substrate and band gap of the SnO2 film increase as the SnO2 content increases, while the absorbance decreases. By analyzing the SEM, UV-Vis, X-ray diffraction (XRD) and steady-state photoluminescence spectrum (PL) analysis of the SnO2/MAPbI3 thin film, it is found that the MAPbI3 deposited on the SnO2 layer with a concentration of 7.5% is uniform and pinhole-free, has the largest particle size and the best crystallinity, as well as more effective charge extraction capability and transport capability. By analyzing the electrochemical impedance (EIS) and external quantum efficiency (EQE) of the device, the SnO2 electron transport layer with a concentration of 7.5% has better interface contact and lower interface resistance, which is beneficial to reducing the recombination of carriers and improving the photoelectric conversion capability, The perovskite solar cells based on SnO2 layer prepared with a concentration of 7.5% reaches a photoelectric conversion efficiency of 15.82% (Voc = 1.06 V, Jsc = 21.62 mA/cm2, FF = 69.40%), After storing for 600 h in ambient air ((25±5) ℃, RH>70%) without encapsulation, its efficiency remains 92% of the initial efficiency. At the same time, we prepare flexible devices on flexible substrates (TIO/PEN) by using SnO2 precursor with a concentration of 7.5%, which exhibits good photovoltaic performance and achieves a photoelectric conversion efficiency of 13.12%, and storage time for 84 d in ambient air ((30±5) ℃, RH>70%) without encapsulation, its efficiency remains 48% of the initial efficiency. The PCE retains 78% of the initial efficiency after 1000 bending cycles with a bending radius of 3 mm. The study of optimizing the concentration of SnO2 has laid a foundation for improving the performance of flexible perovskite solar cells.

Amorphous SnO2 as Earth‐abundant Stable Transparent Conductive Oxide and Its Application to Si Heterojunction Solar Cells

Improved electrical contact properties in Indium-free silicon heterojunction solar cells with amorphous SnO 2 TCO layers

Low‐Cost Tin Oxide Transparent Conductive Films for Silicon Heterojunction Solar Cells

Highly Efficient Silicon Heterojunction Solar Cells with ZnO:Al Transparent Electrode and Transition Metal Doped Indium Oxide Interfacial Layer

ZnO‐doped In2O3 front transparent contact enables >24.0% silicon heterojunction solar cells

Low-cost Sn-doped indium oxide films with high mobility by reactive plasma deposition for silicon heterojunction solar cells

A Brief Review of Transparent Conducting Oxides (TCO): The Influence of Different Deposition Techniques on the Efficiency of Solar Cells

Investigation of In2O3:SnO2 films with different doping ratio and application as transparent conducting electrode in silicon heterojunction solar cell

Effective utilization of light by transparent conducting oxide layer to enhance the performance of the silicon heterojunction solar cells

Hybrid potentiodynamic/potentiostatic electrodeposition of thin and compact tin dioxide on indium tin oxide electrodes

Status and Perspectives of Transparent Conductive Oxide Films for Silicon Heterojunction Solar Cells

Transparent conducting oxide films for thin film silicon photovoltaics

Solution Combustion Synthesis of Transparent Conducting Thin Films for Sustainable Photovoltaic Applications

Application of Indium Tin Oxide/Aluminum-Doped Zinc Oxide Transparent Conductive Oxide Stack Films in Silicon Heterojunction Solar Cells

Constructing tin oxides Interfacial Layer with Gradient Compositions for Efficient Perovskite/Silicon Tandem Solar Cells with Efficiency Exceeding 28%

Modulation of the TCO/MoO x Front Contact Enables >21% High-Efficiency Dopant-Free Silicon Solar Cells

Non-toxic and rapid chemical bath deposition for SnO2 electron transporting layers in perovskite solar cells

Undoped tin dioxide transparent electrodes for efficient and cost-effective indoor organic photovoltaics (SnO2 electrode for indoor organic photovoltaics)

Flexibility of Room-Temperature-Synthesized Amorphous CdO-In 2 O 3 Alloy Films and Their Application as Transparent Conductors in Solar Cells

Bifunctional Surface Engineering on SnO 2 Reduces Energy Loss in Perovskite Solar Cells

Low-temperature Preparation of SnO<sub>2</sub> Electron Transport Layer for Perovskite Solar Cells