Abstract:SnO2 has the advantages of excellent photostability and can be prepared under low-temperature below 200°C. It is regarded as one of the excellent materials for the electron transport layer, and it is widely used in efficient and stable planar heterojunction perovskite solar cells. In this paper, the low-cost, dense and uniform SnO2 electron transport layer is prepared by spin coating at low temperature (150°C) for perovskite solar cells with a structure of FTO / SnO2 / CH3NH3PbI3 (MAPbI3) / Spiro-OMeTAD / Au. The crystallization and photoelectric properties of SnO2 electron transport layers prepared at different concentrations (2.5~10wt%) at 150°C, and the influence of SnO2 electron transport layers on the formation of perovskite films and the performance of perovskite solar cells are discussed. By analyzing the scanning electron microscope (SEM), ultraviolet-visible light absorption spectrum (UV-Vis) and transmission spectrum of the SnO2 film, it is found that the coverage and light transmittance of the substrate and band gap of the SnO2 film will increase as the SnO2 content increase, while the absorbance decreases. By analyzing the SEM, UV-Vis, X-ray diffraction (XRD) and steady-state photoluminescence spectrum (PL) analysis of the SnO2 / MAPbI3 thin film, it is found that the MAPbI3 deposited on the SnO2 layer with concentration of 7.5wt% is uniform and pinhole-free, has the largest particle size and the best crystallinity, as well as more effective charge extraction and transport capabilities. By analyzing the electrochemical impedance (EIS) and external quantum efficiency (EQE) of the device, the SnO2 electron transport layer with a concentration of 7.5wt% has better interface contact and lower interface resistance, which is beneficial to reduce the recombination of carriers and improve the photoelectric conversion ability, The perovskite solar cells based on SnO2 layer prepared with concentration of 7.5wt% obtained the photoelectric conversion efficiency of 15.82% (Voc=1.06V, Jsc=21.62mA/cm2, FF=69.40%), After storing for 600 h in ambient air (25±5°C, RH70%) without encapsulation, it still maintains 92% of the initial efficiency. At the same time, we tried to prepare flexible devices on flexible substrates (TIO/PEN) using SnO2 precursor with a concentration of 7.5wt%, which exhibited good photovoltaic performance and obtained the photoelectric conversion efficiency of 13.12%, and storing for 84 d in ambient air (30±5°C, RH70%) without encapsulation, it still maintains 48% of the initial efficiency. The PCE retains 78% of the initial value after 1000 bending cycles with a bending radii of 3 mm. The study of optimizing the concentration of SnO2 has laid a foundation for improving the performance of flexible perovskite solar cells.

Undoped tin dioxide transparent electrodes for efficient and cost-effective indoor organic photovoltaics (SnO2 electrode for indoor organic photovoltaics)

Low‐Cost Tin Oxide Transparent Conductive Films for Silicon Heterojunction Solar Cells

Efficient Planar Perovskite Solar Cells Using Passivated Tin Oxide as an Electron Transport Layer

Cost‐Effective Transparent N‐Doped Tin Oxide Electrodes with Excellent Thermal and Chemical Stabilities Enabling Stable Perovskite Photovoltaics Based on Tin Oxide Electron Transport Layer

Hybrid potentiodynamic/potentiostatic electrodeposition of thin and compact tin dioxide on indium tin oxide electrodes

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

Naphthalene Diimide-Modified SnO2 Enabling Low-Temperature Processing for Efficient ITO-Free Flexible Perovskite Solar Cells

A low temperature processable tin oxide interlayer via amine-modification for efficient and stable organic solar cells

Low-temperature Preparation of Tin Dioxide Electron Transport Layer in Perovskite Solar Cells

Modification of the SnO2 Electron Transporting Layer by Using Perylene Diimide Derivative for Efficient Organic Solar Cells

Highly efficient and stable organic solar cells with SnO 2 electron transport layer enabled by UV-curing acrylate oligomers

Sn Composition Engineering Toward the Breakthrough of Transparent Front Electrodes for Efficient and Stable Perovskite Solar Cells

Adhesion‐Controlled Heterogeneous Nucleation of Tin Halide Perovskites for Eco‐Friendly Indoor Photovoltaics

A Compact Electron Transport Layer Using a Heated Tin‐Oxide Colloidal Solution for Efficient Perovskite Solar Cells

Copper phosphotungstate as low cost, solution-processed, stable inorganic anode interfacial material enables organic photovoltaics with over 18% efficiency

Managing Interfacial Defects and Charge-Carriers Dynamics by a Cesium-Doped SnO2 for Air Stable Perovskite Solar Cells

Cellulose Nanocrystals–Tin‐Oxide Hybrid Electron Transport Layers for Solar Energy Conversion

Rational Design of A Chemical Bath Deposition Based Tin Oxide Electron Transport Layer for Perovskite Photovoltaics

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

Non-toxic and rapid chemical bath deposition for SnO2 electron transporting layers in perovskite solar cells