Abstract:The development of perovskite solar modules is of essence to commercialization of perovskite photovoltaics regarded as one of the next‐generation sustainable energy conversion technologies. Electron‐transport layer acts as the key factor determining performance and reliability. This work demonstrates surface engineering by pH modulation in SnO2 colloidal dispersion leads to homogeneous and defect‐reduced electron‐transport layer, resulting in high‐performance, and reliability against damp heat and outdoor conditions. Uniform film deposition over an entire substrate is indispensable to achieve efficient perovskite solar modules (PSMs) by minimizing the gap with high‐performance perovskite solar cells (PSCs). Only a few microscopic pinholes on the film in PSMs directly give rise to debase the performance and stimulate the degradation of the devices. Herein, a strategy of the homogeneous and defect‐reduced electron‐transport layer for high‐performance PSMs is reported. pH modulation of tin oxide (SnO2) nanoparticles colloidal dispersion by a small amount of nitric acid (HNO3) addition leads to the removal of hydroxy groups on the SnO2 surface acting as electronic defects as well as superb regularity of the thin films by forming a network of the SnO2 nanoparticles. The surface engineering of SnO2 nanoparticles brings out the high performance of 23.7% efficiency for a unit cell, 20.3% efficiency for a 24.5 cm2 minimodule, and 19.0% efficiency for a 214.7 cm2 submodule, respectively, where all efficiencies are averaged from results obtained by the reverse/forward scan. In outdoor tests with the submodules, a target PSM generates 16.5% higher cumulative electricity for a month as compared to a control PSM. Furthermore, under damp heat environments, the target PSM maintains 80% efficiency compared to an initial efficiency of 1080 h.

Bifunctional Surface Engineering on SnO 2 Reduces Energy Loss in Perovskite Solar Cells

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Surface Engineering of Tin Oxide Nanoparticles by pH Modulation Facilitates Homogeneous Film Formation for Efficient Perovskite Solar Modules

Managing Interfacial Defects and Charge-Carriers Dynamics by a Cesium-Doped SnO2 for Air Stable Perovskite Solar Cells

Facilitating Electron Transport in Perovskite Solar Cells through Tailored SnO2 Film Composition

Simultaneous Passivation of the SnO 2 /Perovskite Interface and Perovskite Absorber Layer in Perovskite Solar Cells Using KF Surface Treatment

Annealing-Free SnO 2 Layers for Improved Fill Factor of Perovskite Solar Cells

Surface Reconstruction for Tin-Based Perovskite Solar Cells

Simultaneous Passivation of the SnO2/Perovskite Interface and Perovskite Absorber Layer in Perovskite Solar Cells Using KF Surface Treatment

Synergetic Optimization of Upper and Lower Surfaces of the SnO2 Electron Transport Layer for High-Performance N-I-p Perovskite Solar Cells

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

Solvent engineering of SnO2 electron transport layer for high-performance perovskite solar cells

Nitrogen‐doped tin oxide electron transport layer for stable perovskite solar cells with efficiency over 23%

Smoothing and coverage improvement of SnO2 electron transporting layer by NH4F treatment: Enhanced fill factor and efficiency of perovskite solar cells

Surface Sn(IV) Hydrolysis Improves Inorganic Sn–Pb Perovskite Solar Cells

Ameliorating the Interfacial Mismatch of SnO2 and Perovskite Enabling High Mechanical Stability for Flexible Perovskite Solar Cells

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

Bifunctional SnO 2 Colloid Offers No Annealing Effect Compact Layer and Mesoporous Scaffold for Efficient Perovskite Solar Cells

Simultaneous Surface Modification and Defect Passivation on Tin Oxide–Perovskite Interfaces using Pseudohalide Salt of Sodium Tetrafluoroborate

Enhanced photovoltaic performance of SnO2 based flexible perovskite solar cells via introducing interfacial dipolar layer and defect passivation

Defect engineering of oxygen vacancies in SnOx electron transporting layer for perovskite solar cells