Abstract:Lead-free double perovskite Cs2AgBiBr6 is considered to serve as a substitute for toxic lead-based perovskite components and is a promising candidate for environmentally friendly perovskite solar cells (PSCs). However, the high deep-level trap density in Cs2AgBiBr6 films hinders the device performance, which is caused by the different solubilities of components in the precursor solution and the solution-process fabrication method. In this work, we reported a surface reconstruction (SR) strategy, in which a dissolution process is initiated by dimethyl sulfoxide (DMSO) and followed by the introduction of methylammonium bromide (MABr) to generate a mixed organic-inorganic intermediate phase and induce an orderly recrystallization. The dissolution-recrystallization process effectively improves the overall crystalline quality and surface composition stoichiometry ratio, passivates the bromine vacancies enriched in the film, and forms a dense as well as ordered film surface, resulting in reduced trap density, extended carrier lifetime, better interfacial contact, and faster carrier extraction. The differences in underlying mechanisms and effects between the conventional interfacial passivation (IP) strategy based on the passivator/isopropanol (IPA) system and the SR strategy proposed in this work were also compared by multiple characterizations. All these advantages enable the Cs2AgBiBr6-based PSCs fabricated by the SR strategy to achieve a significantly higher power conversion efficiency (PCE) of 2.05% and an ultrahigh fill factor (FF) of 83.80% as well as open-circuit voltage (V (OC)) of 1.201 V, with good stability and broad applicability in the hole transport layer (HTL)-free PSCs. Therefore, this work points out the fundamentally different mechanisms of two post-treatment strategies on the overall regulation of Cs2AgBiBr6 films and provides a clear clue to further enhance the quality of lead-free double perovskite films and optimize the photovoltaic performance of PSCs.

Surface Reconstruction for Tin-Based Perovskite Solar Cells

Reconstructing Subsurface Lattice for Stable Perovskite Photovoltaics

Surface Sn(IV) Hydrolysis Improves Inorganic Sn–Pb Perovskite Solar Cells

In Situ Reconstruction of Hole‐Selective Perovskite Heterojunction with Graded Energetics Toward Highly Efficient and Stable Solar Cells

Efficient Passivation Strategy on Sn Related Defects for High Performance All‐Inorganic CsSnI3 Perovskite Solar Cells

Over 14% efficiency of highly reproducible Sn perovskite solar cell via defect passivation and morphology repairment

Surface Reconstruction for Efficient Cs2AgBiBr6 Solar Cells

Surface Reconstruction for Efficient and Stable Monolithic Perovskite/Silicon Tandem Solar Cells with Greatly Suppressed Residual Strain

Rationally reconstructing the surface microstructure of chemical bath deposited electron transport layer for efficient and stable perovskite solar cells

Efficient Passivation Strategy on Sn Related Defects for High Performance All‐Inorganic CsSnI 3 Perovskite Solar Cells

Synchronous Surface Reconstruction and Defect Passivation for High-Performance Inorganic Perovskite Solar Cells.

Surface Reconstruction Strategy Improves the All-Inorganic CsPbIBr2 Based Perovskite Solar Cells and Photodetectors Performance

Surface Reconstruction via Molten Chloride Salt for Efficient and Stable Perovskite Solar Cells

Surface Lattice Engineering Enables Efficient Inverted Perovskite Solar Cells

High‐Stable Lead‐Free Solar Cells Achieved by Surface Reconstruction of Quasi‐2D Tin‐Based Perovskites

Multi-functional Molecule Advancing the Efficiency of Pure 3D FASnI3 Perovskite Solar Cells Based on Tin Tetraiodide Reduction Method

Reconstructing the Amorphous and Defective Surface for Efficient and Stable Perovskite Solar Cells

Thiol Groups Reutilization on Chemical Bath Deposited Tin Oxide Surface Achieving Interface Anchoring and Defects Passivation for Enhancing the Performance and Stability of Perovskite Solar Cells

Ternary‐Metal Sn‐Pb‐Zn Perovskite to Reconstruct Top Surface for Efficient and Stable Less‐Pb Perovskite Solar Cells

Stoichiometric Dissolution of Defective CsPbI 2 Br Surfaces for Inorganic Solar Cells with 17.5% Efficiency

Interfacial Engineering Dominated Passivation Strategy to Facilitate Performance Improvement of Cssncl3 Pscs by Induced Sn-O Bonds: Insight from Dft Calculations and Device Simulations