Abstract:Lead-free double perovskite Cs2AgBiBr6 is considered to serve as a substitute for toxic lead-based perovskite components and is a promising candidate for environmentally friendly perovskite solar cells (PSCs). However, the high deep-level trap density in Cs2AgBiBr6 films hinders the device performance, which is caused by the different solubilities of components in the precursor solution and the solution-process fabrication method. In this work, we reported a surface reconstruction (SR) strategy, in which a dissolution process is initiated by dimethyl sulfoxide (DMSO) and followed by the introduction of methylammonium bromide (MABr) to generate a mixed organic-inorganic intermediate phase and induce an orderly recrystallization. The dissolution-recrystallization process effectively improves the overall crystalline quality and surface composition stoichiometry ratio, passivates the bromine vacancies enriched in the film, and forms a dense as well as ordered film surface, resulting in reduced trap density, extended carrier lifetime, better interfacial contact, and faster carrier extraction. The differences in underlying mechanisms and effects between the conventional interfacial passivation (IP) strategy based on the passivator/isopropanol (IPA) system and the SR strategy proposed in this work were also compared by multiple characterizations. All these advantages enable the Cs2AgBiBr6-based PSCs fabricated by the SR strategy to achieve a significantly higher power conversion efficiency (PCE) of 2.05% and an ultrahigh fill factor (FF) of 83.80% as well as open-circuit voltage (V (OC)) of 1.201 V, with good stability and broad applicability in the hole transport layer (HTL)-free PSCs. Therefore, this work points out the fundamentally different mechanisms of two post-treatment strategies on the overall regulation of Cs2AgBiBr6 films and provides a clear clue to further enhance the quality of lead-free double perovskite films and optimize the photovoltaic performance of PSCs.

Synchronous Surface Reconstruction and Defect Passivation for High-Performance Inorganic Perovskite Solar Cells.

Synchronous surface reconstruction and grain boundary healing toward efficient and stable inverted CsPbI3 perovskite solar cells

Surface Defects Management by In Situ Etching with Methanol for Efficient Inverted Inorganic Perovskite Solar Cells

Illumination Enhanced Crystallization and Defect Passivation for High Performance CsPbI3 Perovskite Solar Cells by Sacrificing Dye

Simultaneous dual-interface and bulk defect passivation for high-efficiency and stable CsPbI2Br perovskite solar cells

Defect Passivation in Perovskite Solar Cells by Cyano‐Based π‐Conjugated Molecules for Improved Performance and Stability

A synchronous defect passivation strategy for constructing high-performance and stable planar perovskite solar cells

Effective defect passivation with a designer ionic molecule for high-efficiency vapour-deposited inorganic phase-pure CsPbBr3 perovskite solar cells

Stoichiometric Dissolution of Defective CsPbI 2 Br Surfaces for Inorganic Solar Cells with 17.5% Efficiency

Pyridalthiadiazole‐Based Molecular Chromophores for Defect Passivation Enables High‐Performance Perovskite Solar Cells

Interfacial Engineering Dominated Passivation Strategy to Facilitate Performance Improvement of Cssncl3 Pscs by Induced Sn-O Bonds: Insight from Dft Calculations and Device Simulations

Surface Defects Passivation with Organic Salt for Highly Stable and Efficient Lead-Free Cs 3 Sb 2 I 9 Perovskite Solar Cells

Enhancing the Performance of Carbon‐Based All‐Inorganic CsPbIBr2 Perovskite Solar Cells via Na2SiO3 Surface Treatment for Passivation of the TiO2/Perovskite Interface

Efficient Passivation Strategy on Sn Related Defects for High Performance All‐Inorganic CsSnI3 Perovskite Solar Cells

A Facile Surface Passivation Method for Efficient Inorganic CsPbI2Br Perovskite Solar Cells with Efficiencies over 15%

In Situ Forming of a 2D Inorganic Perovskite Capping Layer by Surface Reconstruction for Efficient and Stable CsPbI2Br Perovskite Solar Cells

Spatially selective defect management of CsPbI3 films for high-performance carbon-based inorganic perovskite solar cells

Efficient Passivation Strategy on Sn Related Defects for High Performance All‐Inorganic CsSnI 3 Perovskite Solar Cells

Surface Reconstruction for Efficient Cs2AgBiBr6 Solar Cells

Synchronous defect passivation strategy via Lewis base for efficient and stable perovskite solar cells

Efficient Defect Passivation for Perovskite Solar Cells by Controlling the Electron Density Distribution of Donor‐π‐Acceptor Molecules