Abstract:Charge accumulation and charged defects at both bulk and buried heterojunction interfaces of perovskites are primarily related to the photovoltaic performance and shelf stability of perovskite solar cells (PSCs). Moreover, detrimental defects distributing along the perovskite bottom side in contact with the tin oxide (SnO2) surface may exert unparalleled significance in charge extraction and transport. Most importantly, interfacial nonradiative recombination can also widely exist, which will seriously hamper efficiency of the related device. In this work, a multifunctional chemical bridge at the perovskite/SnO2 interface is devised through triggering an in situ polymerization strategy, by which cross-linked polymerizable 3-(trimethoxysilyl)propyl methacrylate (MAPS) monomers under the combination of temperature and initiators can form bulkier macropolymers (MAPS dimers). Detailed theoretical and experimental results reveal that the carbonyl groups (CO) of both MAPS monomers and MAPS dimers can chemically anchor to perovskite bottom side through a CO···Pb coordination bond interaction to regulate the film quality and the siloxane groups effectively couple with oxygen vacancies on the SnO2 film surface to facilitate its optoelectronic properties. Compared with the primitive MAPS monomer units, the resultant MAPS dimers simultaneously prevent interfacial charge accumulation and demonstrate a more benign energy level alignment to further augment photovoltaic performance of PSCs. Thus, the devices assembled under open-air conditions based on double-sided passivation deliver a decent photoelectronic performance with the champion efficiency of 20.94% accompanied by negligible hysteresis. Meanwhile, the unencapsulated targeted devices maintain 93.1% and 86.5% of their original efficiency after continuous 500 h thermal treatment and 500 h light illumination under open-circuit conditions, respectively.

Simultaneous Passivation of the SnO2/Perovskite Interface and Perovskite Absorber Layer in Perovskite Solar Cells Using KF Surface Treatment

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Simultaneous Passivation of the SnO 2 /Perovskite Interface and Perovskite Absorber Layer in Perovskite Solar Cells Using KF Surface Treatment

Multifunctional Thiophene-Based Interfacial Passivating Layer for High-Performance Perovskite Solar Cells

Simultaneous Contact and Grain‐Boundary Passivation in Planar Perovskite Solar Cells Using SnO2‐KCl Composite Electron Transport Layer

Surface passivation of perovskite films by potassium bis(fluorosulfonyl)imide for efficient solar cells

Synergistic dual-layer passivation boosts efficiency and stability in perovskite solar cells using naphthol sulfonate

Realizing High‐Efficiency Perovskite Solar Cells by Passivating triple cation perovskite films

Multifunctional Interface Treatment of Phosphate for High-Efficiency Perovskite Solar Cells

Synergetic Optimization of Upper and Lower Surfaces of the SnO2 Electron Transport Layer for High-Performance N-I-p Perovskite Solar Cells

Enhanced photovoltaic performance of SnO2 based flexible perovskite solar cells via introducing interfacial dipolar layer and defect passivation

Highly improved efficiency and stability of planar perovskite solar cells via bifunctional phytic acid dipotassium anchored SnO2 electron transport layer

Interfacial Engineering Dominated Passivation Strategy to Facilitate Performance Improvement of Cssncl3 Pscs by Induced Sn-O Bonds: Insight from Dft Calculations and Device Simulations

Focusing on the bottom contact: Carbon quantum dots embedded SnO2 electron transport layer for high-performance and stable perovskite solar cells

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells

Surface Defect Passivation and Energy Level Alignment Engineering with a Fluorine-Substituted Hole Transport Material for Efficient Perovskite Solar Cells

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO 2 ‐Based Electron Transport Layers

Buried Interface Engineering‐Assisted Defects Control and Crystallization Manipulation Enables Stable Perovskite Solar Cells with Efficiency Exceeding 25%

Passivation Mechanism of Perovskite Upper Interface based on MAPbBr3 Quantum Dots for Efficient and Stable Perovskite Solar Cells

Synergistic effect of multifunctional MXene-nanosheet and naphthoquinone sulfonate toward high-performance perovskite solar cells and modules