Abstract:In this work, the SnO 2 -Ti 3 C 2 hybrid electron transport layer (ETL) was prepared by incorporating two-dimensional Ti 3 C 2 -MXene into SnO 2 and appropriate ultraviolet (UV) ozone treatment. The synergistic effect of Ti 3 C 2 introduction and UV ozone treatment on the charge transport capacity of SnO 2 ETL, interface properties of ETL/perovskite, perovskite morphology, and device performance was systematically investigated. The results show that the introduction of Ti 3 C 2 does not affect the morphology and transmittance of SnO 2 ETL. The perovskite films based on SnO 2 -Ti 3 C 2 are not only dense, but also have smaller surface roughness, more uniform, and larger grain size, even penetrating the entire perovskite film. The surface oxidation of Ti 3 C 2 induced by UV-ozone treatment enhanced the charge transport capacity of ETL. The electron extraction and charge transfer at the interface between SnO 2 -Ti 3 C 2 ETL and perovskite are higher, and carrier recombination is effectively suppressed. Perovskite solar cells (PSCs) based on SnO 2 -Ti 3 C 2 ETL have larger charge recombination impedance and higher electron mobility, mainly due to enhanced ETL charge transport and optimization of interface properties. The short-circuit current ( J sc) and filling factor (FF) of PSCs are increased by 5% and 7% respectively, delivering a champion device with a relatively high FF of 79.38% and high power conversion efficiency of 19.52%, as well as good stability. Thus, this study provides a simple and effective method for the preparation of efficient and repeatable PSCs and paves the way for the industrialization of PSCs to a certain extent.

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Enhancing electron extraction and transport in inorganic perovskite solar cells via additional built-in potential of SnO 2 -BiFeO 3 nano-heterostructure

Enhanced Efficiency and Stability of Planar Perovskite Solar Cells Using SnO2:InCl3 Electron Transport Layer Through Synergetic Doping and Passivation Approaches

Multi-cation hybrid stannic oxide electron transport layer for high-efficiency perovskite solar cells

SnO2/2D-Bi2O2Se New Hybrid Electron Transporting Layer for Efficient and Stable Perovskite Solar Cells

Superior SnO2 Electron Transport Layer Via Bifunctional Interfacial Regulation Using Cesium Sulfate for Efficient Perovskite Solar Cell

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO2‐Based Electron Transport Layers

Improvement of Nanopore Structure SnO2 Electron-Transport Layer for Carbon-Based CsPbIBr2 Perovskite Solar Cells

Modification of SnO2 electron transport Layer: Brilliant strategies to make perovskite solar cells stronger

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO 2 ‐Based Electron Transport Layers

SnO<sub>2</sub> Passivation and Enhanced Perovskite Charge Extraction with a Benzylamine Hydrochloric Interlayer

TiO2/SnO2 Electron Transport Double Layers with Ultrathin SnO2 for Efficient Planar Perovskite Solar Cells

Novel Bilayer SnO2 Electron Transport Layers with Atomic Layer Deposition for High-Performance α-FAPbI3 Perovskite Solar Cells.

The low temperature solution-processable SnO2 modified by Bi2O2S as an efficient electron transport layer for perovskite solar cells

Enhanced Electrons Extraction of Lithium-Doped SnO$_{2}$ Nanoparticles for Efficient Planar Perovskite Solar Cells

Embedding SnO2 Thin Shell Protected Ag Nanowires in SnO2 ETL to Enhance the Performance of Perovskite Solar Cells.

SnO2-Based Perovskite Solar Cells: Configuration Design and Performance Improvement

Electron Transporting Bilayer of SnO2 and TiO2 Nanocolloid Enables Highly Efficient Planar Perovskite Solar Cells

Strategy of Enhancing Built-in Field to Promote the Application of C-TiO2/SnO2 Bilayer Electron Transport Layer in High-Efficiency Perovskite Solar Cells (24.3%)

SnO2-Ti3C2 Blends As Electron Transport Layer for Efficient and Easily Fabricated Planar Perovskite Solar Cells

Round-comb Fe2O3@SnO2 Heterostructures Enable Efficient Light Harvesting and Charge Extraction for High-Performance All-Inorganic Perovskite Solar Cells.