Abstract:In this work, the SnO 2 -Ti 3 C 2 hybrid electron transport layer (ETL) was prepared by incorporating two-dimensional Ti 3 C 2 -MXene into SnO 2 and appropriate ultraviolet (UV) ozone treatment. The synergistic effect of Ti 3 C 2 introduction and UV ozone treatment on the charge transport capacity of SnO 2 ETL, interface properties of ETL/perovskite, perovskite morphology, and device performance was systematically investigated. The results show that the introduction of Ti 3 C 2 does not affect the morphology and transmittance of SnO 2 ETL. The perovskite films based on SnO 2 -Ti 3 C 2 are not only dense, but also have smaller surface roughness, more uniform, and larger grain size, even penetrating the entire perovskite film. The surface oxidation of Ti 3 C 2 induced by UV-ozone treatment enhanced the charge transport capacity of ETL. The electron extraction and charge transfer at the interface between SnO 2 -Ti 3 C 2 ETL and perovskite are higher, and carrier recombination is effectively suppressed. Perovskite solar cells (PSCs) based on SnO 2 -Ti 3 C 2 ETL have larger charge recombination impedance and higher electron mobility, mainly due to enhanced ETL charge transport and optimization of interface properties. The short-circuit current ( J sc) and filling factor (FF) of PSCs are increased by 5% and 7% respectively, delivering a champion device with a relatively high FF of 79.38% and high power conversion efficiency of 19.52%, as well as good stability. Thus, this study provides a simple and effective method for the preparation of efficient and repeatable PSCs and paves the way for the industrialization of PSCs to a certain extent.

The low temperature solution-processable SnO2 modified by Bi2O2S as an efficient electron transport layer for perovskite solar cells

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Modification of SnO2 electron transport Layer: Brilliant strategies to make perovskite solar cells stronger

Poly(vinylpyrrolidone)-doped SnO2 as an electron transport layer for perovskite solar cells with improved performance

Optimized SnO2 preparation and coherent interlayers for enhanced charge dynamics and efficient perovskite photovoltaics

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Enhanced Electronic Properties of SnO2 via Electron Transfer from Graphene Quantum Dots for Efficient Perovskite Solar Cells.

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

A low-temperature TiO2/SnO2 electron transport layer for high-performance planar perovskite solar cells

Low Temperature Solution-Processed Sb : SnO 2 Nanocrystals for Efficient Planar Perovskite Solar Cells

Heterovalent Samarium Cation‐Doped SnO2 Electron Transport Layer for High‐Efficiency Planar Perovskite Solar Cells

Synergetic Optimization of Upper and Lower Surfaces of the SnO2 Electron Transport Layer for High-Performance N-I-p Perovskite Solar Cells

Yb-doped SnO2 electron transfer layer assisting the fabrication of high-efficiency and stable perovskite solar cells in air

Enhancing electron extraction and transport in inorganic perovskite solar cells via additional built-in potential of SnO 2 -BiFeO 3 nano-heterostructure

SnO2-Ti3C2 Blends As Electron Transport Layer for Efficient and Easily Fabricated Planar Perovskite Solar Cells

Polyelectrolyte-Doped SnO<sub>2</sub> as a Tunable Electron Transport Layer for High-Efficiency and Stable Perovskite Solar Cells

Multifunctional Organic Salt Regulated SnO2 Electron Transport Layer/Perovskite Interface for High Air‐Stable Perovskite Solar Cells

Solvent engineering of SnO2 electron transport layer for high-performance perovskite solar cells

Robust Electron Transport Layer of SnO2 for Efficient Perovskite Solar Cells: Recent Advances and Perspectives

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

3,5-Difluorophenylboronic acid-modified SnO2 as ETLs for perovskite solar cells: PCE > 22.3%, T82 > 3000 h