Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Focusing on the bottom contact: Carbon quantum dots embedded SnO2 electron transport layer for high-performance and stable perovskite solar cells

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Simultaneous bottom-up double-layer synergistic optimization by multifunctional fused-ring acceptor with electron-deficient core for stable planar perovskite solar cells with approaching 24% efficiency

Bottom Contact Engineering for Ambient Fabrication of >25% Durable Perovskite Solar Cells

Zirconium acetate stabilized tin dioxide colloidal quantum dots as multifunctional electron transporting layer for efficient and stable perovskite solar cells

Synergetic Optimization of Upper and Lower Surfaces of the SnO2 Electron Transport Layer for High-Performance N-I-p Perovskite Solar Cells

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO 2 ‐Based Electron Transport Layers

CsI Enhanced Buried Interface for Efficient and UV‐Robust Perovskite Solar Cells

Stabilizing Bottom Side of Perovskite via Preburying Cesium Formate toward Efficient and Stable Solar Cells

Synergetic modification on buried and upper surfaces of perovskites with nitrogen-doped carbon quantum dots for efficient and stable solar cells

Simultaneous Passivation of the SnO2/Perovskite Interface and Perovskite Absorber Layer in Perovskite Solar Cells Using KF Surface Treatment

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

Room-temperature multiple ligands-tailored SnO2 quantum dots endow in situ dual-interface binding for upscaling efficient perovskite photovoltaics with high VOC

High‐Efficiency and Stable Perovskite Solar Cells via Buried Interface Modification with Multi‐Functional Phosphorylcholine Chloride

Bottom‐Up Defect Modification Through Oily‐Allicin Modified Buried Interface Achieving Highly Efficient and Stable Perovskite Solar Cells

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

Improvement of Photovoltaic Performance of Perovskite Solar Cells by Synergistic Modulation of SnO2 and Perovskite via Interfacial Modification

Low‐Temperature Solution‐Processed ZnO Electron Transport Layer for Highly Efficient and Stable Planar Perovskite Solar Cells with Efficiency over 20%

In situ Ligand‐Managed SnO2 Electron Transport Layer for High‐Efficiency and Stable Perovskite Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Polydentate Ligand Reinforced Chelating to Stabilize Buried Interface toward High‐Performance Perovskite Solar Cells