Abstract:Non-conventional collectors where organic fluid or refrigerant experience a phase change have many advantages over conventional collectors which have either air or relatively high temperature boiling liquid. Increase in heat transfer coefficient and system efficiency, corrosion prevention and freeze protection are the main benefits of the first type. In this study, a detailed numerical model of a flat plate collector is developed to investigate the fluid mean temperature, useful heat gain and heat transfer coefficient along the collector tube. The refrigerant HFC-134a was used in the simulation as the working fluid of the collector. The model can both predict the location where the fluid undergoes a phase change in the tube and the state at the exit under given inlet conditions. The effect of boiling on the heat transfer coefficient of the fluid is also investigated. Simulations were performed at three different mass flow rates (0.001, 0.005 and 0.01 kg/s) and three different operating pressures (4, 6 and 8 bar) to be able to see the effect of mass flow rate and pressure on plate temperature, heat loss coefficient, efficiency of the collector and the heat transfer coefficient of the fluid. The simulation results indicate that the heat transfer coefficient of the fluid increases from 153.54 W/m(2) K to 610.27 W/m(2) K in multiphase flow region. In the liquid single phase region, the collector efficiency rises from 60.2% to 68.8% and the heat transfer coefficient of the fluid increases from 39.24 W/m(2) K to 392.31 W/m(2) K with an increased flow rate whereas the collector efficiency decreases from 72.5% to 62.3% as the operating pressure increases from 4 bar to 8 bar. In order to validate the simulation model an experimental test rig was built and the experiments were performed with HFE 7000 as working thermo-fluid. A new simulation model utilizing HFE 7000 has been developed and the outlet temperature of the fluid was compared with the measured outlet temperature. Both measured and simulated results have shown close conformity. (C) 2015 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).

Experimentally validated axisymmetric simulation for thermo-fluid performance of an active flat-plate solar water heater at low flow rates

Mathematical Modelling and Simulation of Multiphase Flow in a Flat Plate Solar Energy Collector

Numerical analysis with experimental validation for thermal performance of flat plate solar water heater using CuO/distilled water nanofluid in closed loop

Numerical Simulation of the Thermal Performance of a Tubular Solar Air Heater

Thermal analysis of a flat-plate solar collector filled with water under the dynamic operation via a multiparameter sensitivity analysis utilizing the Monte-Carlo method

Experimental and numerical study to develop TRANSYS model for an active flat plate solar collector with an internally serpentine tube receiver

Thermo-Fluid Characteristics of a Flat-Plate Collector with Different Riser Tube Configurations Employing ZnO/Water Nanofluids: An Experimental and Numerical Analysis

Experimental and Numerical Study of Thermal Performance for Flat Plate Solar Water Heater in Najaf

Energy and exergy analysis of conventional and modified flat-plate solar collector with dual spiral flow tubes: A comparative study

Numerical and experimental study of thermal efficiency of a spiral flat plate solar collector by changing the spiral diameter, flow rate, and pipe diameter

Numerical and experimental analysis of the flat plate solar water heater systems' thermal performance

Experimental study on thermal performance of reverse flow solar collector for dual heating applications

Thermal Performance Analysis of Porous Foam-Assisted Flat-Plate Solar Collectors with Nanofluids

Investigation of the enhancement of heat transfer in a flat plate solar collector with a corrugated tube under thermosiphon effect

CFD Analysis of Heat Transfer Enhancement in a Flat-Plate Solar Collector/Evaporator with Different Geometric Variations in the Cross Section

Performance Analysis and Optimization of a Vapor-filled Flat-plate Solar Collector

Numerical Analysis and Experimental Validation of Heat Transfer Characteristic for Flat-Plate Solar Air Collector

Numerical Study to Investigate the Performance of U-shaped Flat Plate Solar Collector Using Phase Change Materials (PCMs)

Application of response surface methodology and computational fluid dynamics for analyzing and optimizing the performance of finned solar air heater

Thermal performance simulation of parabolic trough collector with ternary nanofluid flows and half-star-shaped fins inserts in different receivers

Numerical and experimental investigation of heat transfer of longitudinal fin with varying pitch length in flat plate solar air heater