Abstract:Non-conventional collectors where organic fluid or refrigerant experience a phase change have many advantages over conventional collectors which have either air or relatively high temperature boiling liquid. Increase in heat transfer coefficient and system efficiency, corrosion prevention and freeze protection are the main benefits of the first type. In this study, a detailed numerical model of a flat plate collector is developed to investigate the fluid mean temperature, useful heat gain and heat transfer coefficient along the collector tube. The refrigerant HFC-134a was used in the simulation as the working fluid of the collector. The model can both predict the location where the fluid undergoes a phase change in the tube and the state at the exit under given inlet conditions. The effect of boiling on the heat transfer coefficient of the fluid is also investigated. Simulations were performed at three different mass flow rates (0.001, 0.005 and 0.01 kg/s) and three different operating pressures (4, 6 and 8 bar) to be able to see the effect of mass flow rate and pressure on plate temperature, heat loss coefficient, efficiency of the collector and the heat transfer coefficient of the fluid. The simulation results indicate that the heat transfer coefficient of the fluid increases from 153.54 W/m(2) K to 610.27 W/m(2) K in multiphase flow region. In the liquid single phase region, the collector efficiency rises from 60.2% to 68.8% and the heat transfer coefficient of the fluid increases from 39.24 W/m(2) K to 392.31 W/m(2) K with an increased flow rate whereas the collector efficiency decreases from 72.5% to 62.3% as the operating pressure increases from 4 bar to 8 bar. In order to validate the simulation model an experimental test rig was built and the experiments were performed with HFE 7000 as working thermo-fluid. A new simulation model utilizing HFE 7000 has been developed and the outlet temperature of the fluid was compared with the measured outlet temperature. Both measured and simulated results have shown close conformity. (C) 2015 The Authors. Published by Elsevier Ltd. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).

Thermal analysis of a flat-plate solar collector filled with water under the dynamic operation via a multiparameter sensitivity analysis utilizing the Monte-Carlo method

CFD-thermal analysis of flat plate solar collector for different temperature variations

Performance Analysis and Optimization of a Vapor-filled Flat-plate Solar Collector

Modeling and optimizing the thermodynamics of a flat plate solar collector in transient mode for economic purposes

Mathematical Modelling and Simulation of Multiphase Flow in a Flat Plate Solar Energy Collector

Experimentally validated axisymmetric simulation for thermo-fluid performance of an active flat-plate solar water heater at low flow rates

Dynamic Simulation and Optimization of Flat Plate Solar Collector Parameters Using the MATLAB Program for Erbil-Iraq Climate Condition

Dynamic Performance Analysis of Photovoltaic–thermal Solar Collector with Dual Channels for Different Fluids

Numerical Study to Investigate the Performance of U-shaped Flat Plate Solar Collector Using Phase Change Materials (PCMs)

Thermal Performance of a Flat-Plate Solar Collector for Drying Agricultural Crops

Performance study of parabolic trough solar collector using hybrid nanofluids under Jordanian weather conditions

Numerical and experimental study of thermal efficiency of a spiral flat plate solar collector by changing the spiral diameter, flow rate, and pipe diameter

Experimental, Study and Design Sensitivity Analysis of a Heat Pipe Photovoltaic/thermal System

Dynamic performances modeling of a photovoltaic-thermal collector with water heating in buildings

Experimental and numerical study to develop TRANSYS model for an active flat plate solar collector with an internally serpentine tube receiver

A dynamic thermal performance model for flat-plate solar collectors based on the thermal inertia correction of the steady-state test method

Influence of operating conditions on solar energy utilization efficiency of flat plate solar collector

Thermal–Hydraulic Performance of Flat‐Plate Solar Collector Plant Using Different Heat‐Transfer Fluids

A Parametric Study on the Performance Characteristics of an Evacuated Flat-Plate Photovoltaic/thermal (PV/T) Collector

Sensitivity Analysis of the Concentrated Photovoltaic/Thermal Solar Air Collector with PCM

Thermal Loss Analysis of a Flat Plate Solar Collector Using Numerical Simulation