Abstract:Residual stress constitutes an integral part of the total stress acting on any component in service. It is imperative to determine residual stress to estimate the life of critical engineering components, especially those that are welded. The stresses caused by non-uniform temperature distribution due to welding and the effect of these multiaxial stresses upon service performance are discussed. A controlled thermal severity test (CTS) was performed on mild steel plates bolted together, with anchor welds deposited on opposite sides. After cooling, bithermal and trithermal test welds were deposited one after the other. Varying welding stresses were deliberately introduced by using different thicknesses of both plates to change the thermal severity numbers (TSN). The main experimental technique used here to determine the magnitude and nature of residual stress is based on X-ray diffraction (XRD). It was utilised to develop and standardise other techniques. The XRD method is based on the peak shiftin the diffraction profile due to the presence of stress using a sin2 ψ method. The peak shift is determined by orienting the sample at different angles ± ψ to the incident X-ray beam. The semidestructive technique of hole drilling and use of a strain gauge was also employed to determine residual stress in CTS specimens. The magnitude, nature, and direction of principal stresses were determined by relieving stresses through incremental blind hole drilling and measuring strain values at each step. The surface displacements arising due to hole drilling can also be determined by laser holography. A sandwich holography technique was developed to avoid unwanted rigid body motions of samples due to hole drilling when relieving stresses. Stress values were obtained by measuring fringe displacement between two exposures of a sandwich hologram, due to hole drilling. Results on the change in residual stress values with TSN are discussed. The residual stress values determined by XRD and sandwich holography were found to be comparable, and stress values obtained by hole drilling/strain gauge measurement were higher than these values. The reasons are discussed.

Effect of simulated axial residual stress and transverse residual stress in welded P92 pipe and plates including plasticity error

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

Effect of Welding Residual Stress on Plastic Buckling of Axially Compressed Cylindrical Shells with Patterned Welds

Experimental and Numerical Characterization of Low Cycle Fatigue and Creep Fatigue Behaviour of P92 Steel Welded Joint

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Quantitative description between pre-fatigue damage and residual tensile properties of P92 steel

Residual-Stress, Material Characterization in P22 HRSG-Pipeline Butt Joint

Development and comparison of residual stress measurement on welds by various methods

Stress biaxiality-based residual stress assessment in welded T-joints using the blind-hole method

Numerical Simulation to Study the Effect of Arc Travelling Speed and Welding Sequences on Residual Stresses in Welded Sections of New Ferritic P92 Pipes

Residual Stress Formation and Distortion in Austenitic AISI304 Steel Pipe Weldment with Consideration of Latent Heat using Novel Prescribed Weld Temperature

Thermal-Mechanical Fatigue Behavior of P92 T-Piece Pipe

Numerical and Experimental Analysis of Dissimilar Repair Welding Residual Stress in P91 Steel Considering Solid-State Phase Transformation

Influence of filler metal on residual stress in multi-pass repair welding of thick P91 steel pipe

Exploring Through-Thickness Residual Stress Distribution in Double V-Groove Multipass Welds of High-Strength Low-Alloy Steel and the Impact of Mechanical Restraints

Effect of joint design on residual stresses in AISI-304 stainless steel weldment - a numerical study

Effects of Welding and Constraint Conditions on the Welding Residual Stress and Hardness of Type 316 Stainless Steel Pipe

Effect of Groove Design and Post-Weld Heat Treatment on Microstructure and Mechanical Properties of P91 Steel Weld