Abstract:Introduction The Biggest challenges coal-fired power plants are facing are improving their energy efficiencies and reducing their environmental impact due to CO2 and NOX emissions, can be attained by maximizing the steam pressure and temperature. However, the operating temperatures and pressures in boiler materials were restricted due to limited weldability of essential dissimilar joints between Austenitic Stainless Steel (ASS) and Creep-Enhanced Ferritic Steel (CEFS) due to carbon migration and sensitization. Present research work provides enhanced metallurgical and mechanical properties of weldment by optimizing the welding process and welding parameters. Aim The aim of the manuscript is to explores the welding compatibility of TP347H (stabilized ASS) with solution annealed T91 (CEFS), by Auto TIG welding technique, such that carbon migration at the fusion line of SA213 T91 and sensitization in the heat affected zone of TP347H can be minimized. Methods Influence of Auto TIG welding parameters on the mechanical, microstructure, and corrosion properties are studied and discussed. Carbon migration, mechanical and corrosion properties for lower (0.792 KJ/mm) and higher (1.124 KJ/mm) heat inputs weldments were compared. Investigation on mechanical properties test such as tensile, hardness, and root bend performed as per American Society of Mechanical Engineers (ASME) Section IX. Optical microscopy and Analytical Scanning Electron Microscope (SEM) coupled with Energy Dispersive Spectroscopy (EDS) have been performed to investigate carbon migration and sensitization behaviour. Sensitization susceptibility further validated by American Society for Testing and Materials (ASTM) A 262 Practice E. Results Investigation on tensile, hardness, and root bend tests revealed that mechanical properties for lower heat input weldment were superior. Restricted carbon migration due to optimized heat input improves mechanical properties and this was evidenced by satisfactory results of the bend test which showed no opening at the fusion line. A noticeable improvement in Ultimate Tensile Strength (UTS) 666 and 680N/mm2 (compared to 578 and 561N/mm2 for 1.124 KJ/mm heat input) and an acceptable hardness of 307 HV (compared to 399 HV for 1.124 KJ/mm heat input) were observed at T91 and weld metal interface. No fissures on bend surface and no Cr23C6 precipitation at grain boundary after performing ASTM A 262 Practice E and SEM-EDS respectively on heat affected zone (TP347H) of lower heat input weldment which shows higher resistance to intergranular corrosion (Sensitization). Conclusion Optimizing the welding parameters and decreasing the heat input mitigate the carbon migration at T91 fusion zone and, meeting the requirements for satisfactory mechanical properties in materials used for power generation applications. Further optimized welding heat input have lesser Cr23C6 precipitation in the heat-affected zone of TP347H, making the heat affected zone less susceptible to sensitization. Heat input must be controlled to (1) avoid intergranular corrosion failure or sensitization and (2) improve the mechanical properties of the weldment where requirement of post weld heat treatment is mandatory in the application (as recommended in the ASME Section 1, PW 39.1).

Residual Stress Formation and Distortion in Austenitic AISI304 Steel Pipe Weldment with Consideration of Latent Heat using Novel Prescribed Weld Temperature

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

Effects of Welding and Constraint Conditions on the Welding Residual Stress and Hardness of Type 316 Stainless Steel Pipe

Distortion and residual stresses in thick plate weld joint of austenitic stainless steel: Experiments and analysis

Effect of Process Parameters on Welding Residual Stress of 316L Stainless Steel Pipe

Three-dimensional finite element modelling of welding residual stresses of medium carbon steel pipes with consideration of solid-state austenite-martensite transformation and post-weld heat treatment

Numerical and Experimental Analysis of Dissimilar Repair Welding Residual Stress in P91 Steel Considering Solid-State Phase Transformation

Residual Stress Analysis in Pipe Welding ASTM A106 Grade B Using FEM Simulation

Numerical Simulation to Study the Effect of Arc Travelling Speed and Welding Sequences on Residual Stresses in Welded Sections of New Ferritic P92 Pipes

A parametric study of thermal and residual stress fields in lined pipe welding

Numerical Simulation of Welding for Residual Stress Prediction of Low Carbon Steel

Modeling of welding residual stress in a dissimilar metal butt-welded joint between P92 ferritic steel and SUS304 austenitic stainless steel

Effect of joint design on residual stresses in AISI-304 stainless steel weldment - a numerical study

Mechanical and intergranular corrosion properties of auto TIG welded TP347H-T91 dissimilar weldments

Role of welding residual stress in stainless steel piping with application of the leak-before-break technology

Numerical Investigation on Stress Distribution and Evolution in 9cr/2.25cr Dissimilar Welded Rotor Undergoing Welding and Heat Treatment

Residual stress simulation in thin and thick-walled stainless steel pipe welds including pipe diameter effects

Residual-Stress, Material Characterization in P22 HRSG-Pipeline Butt Joint

Degradation of Mechanical Properties in Austenitic Stainless Steel Pipe and Fittings for Corrosive Refinery Applications