Abstract:Welding residual stress (WRS) significantly influences the fatigue life and safety of welded steel structures. Post-weld heat treatment (PWHT) is a common method employed to mitigate WRS. In present study, the WRS evolution law and relaxation mechanism of U-rib-to-deck joints was investigated during PWHT. High-temperature heat treatment tests with varying holding times were conducted on U-rib-to-deck joints to reduce WRS. The WRS distributions were measured using the hole-drilling method before and after PWHT. ABAQUS software, incorporating the Norton-Bailey creep constitutive model, was employed to simulate the WRS evaluation during both welding and PWHT processes. The simulated values were validated against the measured data, and the effects of different holding times, holding temperatures, and heating and cooling rates during PWHT on WRS relaxation were discussed. The results demonstrate that PWHT effectively reduces WRS and leads to a more uniform distribution. Extending the PWHT holding time from 0.5 h to 1 h and 2 h results in a gradual decrease in WRS relaxation at 600 °C, primarily occurring in the high-value stress region of the weld zone with a small amplitude. Elevating the PWHT temperature from 500 °C to 550 °C and subsequently to 600 °C amplifies the significance of WRS relaxation. Variations in heating and cooling rates (200 °C/h and 80 °C/h, 100 °C/h and 40 °C/h, 50 °C/h and 20 °C/h) lead to a gradual decrease in WRS relaxation across the entire model. Furthermore, considering the creep effect, the stress relaxation rate in the weld is approximately 70 %–80 %, which found to be about 2–3 times higher than that without considering the creep effect. By understanding the evolution law and relaxation mechanism, this study provides valuable insights for designing PWHT processes and assessing their impact on structural safety and fatigue life.

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Effect of Welding Residual Stress on Plastic Buckling of Axially Compressed Cylindrical Shells with Patterned Welds

Buckling Strength of Tapered Cylindrical Shells under Partial Axial Compression: Effect of Circumferential Weld-Induced Imperfections

Effect of Weld Reinforcement on Axial Plastic Buckling of Welded Steel Cylindrical Shells

Research Of Weld On Axial Buckling Stress Of Multilayer Combined Cylindrical Shells

Experimental and numerical study on compressive behavior of welded hollow spherical joints with external stiffeners

Effect of Weld on Axial Buckling of Cylindrical Shells

Form of Circumferential Weld-Induced Imperfections for Tapered-Wall Cylindrical Shell Structures

Effect of Local Geometric Imperfections on Axial Buckling of Welded Steel Tanks

Influence of post-weld heat treatment on welding residual stress in U-rib-to-deck joint

Effect of Welding Defects on Mechanical Properties of Welded Joints Subjected to Temperature

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Effect of Residual Stress on the Ultimate Bearing Capacity of Titanium Alloy Pressure Spherical–Cylindrical-Combined Shells

Numerical Investigation on Stress Distribution and Evolution in 9cr/2.25cr Dissimilar Welded Rotor Undergoing Welding and Heat Treatment

Effect of welding residual stress on the performance of CFST tubular joints

PWHT influence on welding residual stress in 45 mm bridge steel butt-welded joint

Residual stresses evolution during strip clad welding, post welding heat treatment and repair welding for a large pressure vessel

Effect of Local Rapid Cooling Heat Treatment on Residual Stress of Pressure Vessel Inner Wall Welding Layer

Thermal Effect of Welding on Mechanical Behavior of High-Strength Steel

Local Post Weld Heat Treatment of a Pressure Vessel: A Postmortem Evaluation

EFFECTS OF POST HEAT TREATMENT ON FATIGUE CRACK BEHAVIOR OF ELECTRON-BEAM-WELDED 30crmnsini2a STEEL