Abstract:316L stainless steel pipes are widely used in the storage and transportation of low-temperature media due to their excellent low-temperature mechanical properties and corrosion resistance. However, due to their low thermal conductivity and large coefficient of linear expansion, they often lead to significant welding residual tensile stress and thermal cracks in the weld seam. This also poses many challenges for their secure and reliable applications. In order to effectively control the crack defects caused by stress concentration near the heat-affected zone of the weld, this paper establishes a thermal elastoplastic three-dimensional finite element (FE) model, constructs a welding heat source, and simulates and studies the influence of process parameters on the residual stress around the pipeline circumference and axial direction in the heat-affected zone. Comparison and verification were conducted using simulation and experimental methods, respectively, proving the rationality of the finite element model establishment. The axial and circumferential residual stress distribution obtained by the simulation method did not have an average deviation of more than 30 MPa from the numerical values obtained by the experimental method. This study also considers the effects of welding energy, welding speed, and welding start position on the pipe's circumferential and axial residual stress laws. The results indicate that changes in welding energy and welding speed have almost no effect on the longitudinal residual stress but have a more significant effect on the transverse residual stress. The maximum transverse residual stress is reached at a welding energy of 1007.4~859.3 J/mm and a welding speed of 6.6 mm/s. Various interlayer arc-striking deflection angles can impact the cyclic phase angle of the transverse residual stress distribution in the seam center, but they do not alter its cyclic pattern. They do influence the amplitude and distribution of the longitudinal residual stress along the circumference. The residual stress distribution on the surface of the pipe fitting is homogenized and improved at 120°.

Effect of Local Rapid Cooling Heat Treatment on Residual Stress of Pressure Vessel Inner Wall Welding Layer

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

The primary-auxiliary local post-welding heat treatment method to control welding residual stresses for pressure vessels

Effect of postweld heat treatment on microstructure and properties of stainless steel surfacing layer of CAP1400 evaporator pressure boundary weld

Finite Element Analysis of the Effect of Welding Heat Input and Layer Number on Residual Stress in Repair Welds for a Stainless Steel Clad Plate

Effect of Process Parameters on Welding Residual Stress of 316L Stainless Steel Pipe

Residual stresses evolution during strip clad welding, post welding heat treatment and repair welding for a large pressure vessel

Effects of Welding and Constraint Conditions on the Welding Residual Stress and Hardness of Type 316 Stainless Steel Pipe

Using reinforce plate to control the residual stresses and deformation during local post-welding heat treatment for ultra-large pressure vessels

Impacts of Stress Relief Treatments on Microstructure, Mechanical and Corrosion Properties of Metal Active-Gas Welding Joint of 2205 Duplex Stainless Steel

Study on Peeling Behavior of Stainless Steel Surfacing Layer in Pressure Vessel

Residual Stress of Laser Welding Joint of Stainless Steel Automobile Vent Pipel

Effects Of Vibratory Weld Conditioning And Wind Cooling Method On The Residual Stresses And Transverse Contraction Distortion In Multipass Welding

A Study of Residual Stress in the Repair Weld of Stainless Steel Clad Plate by Neutron Diffraction Measurement and Finite Element Method

Evolution of Residual Stresses in Dissimilar Steel Surfacing Layers During Process of Post-Weld Heat Treatment

Research on Light-Weighting Mechanism of Pressure Strengthening for Austenitic Stainless Steels Cryogenic Vessels

The strengthening role of post-welded cryogenic treatment on the performance and microstructure of 304 austenitic stainless steel weldments

A Study on the Ultrasonic Regulation of the Welding Performance and Residual Stress of 316L Stainless Steel Pipes

A rigid-flexible coordinated method to control weld residual stress and deformation during local PWHT for ultra-large pressure vessels

Role of welding residual stress in stainless steel piping with application of the leak-before-break technology

Effect of Welding Technologies on Decreasing Welding Residual Stress of Francis Turbine Runner