Abstract:The thickness of steel plates used in the member has gradually increased to meet the load-bearing capacity requirements of long-span steel bridges. As the primary connection method of thick steel plate, welding will result in considerable welding residual stress with complex distribution. Large welding residual stress will significantly impact the performance of steel bridges. In this paper, the distribution of residual stress in welded thick steel plate is systematically studied, a specimen with a thickness of 80 mm was designed and fabricated, and the welding residual stress was measured by X-ray diffraction. The finite element model was established and verified by test results. Subsequently, the finite element calculation of the welding residual stress of steel plates with thicknesses of 20, 40, 60, 80, and 100 mm was carried out, and the distribution of surface residual stress and the influence of plate thickness on residual surface stress were studied; then the spatial evolution mechanism of welding residual stress was studied, and the distribution of residual stress inside steel plate and the influence of plate thickness on the distribution of residual stress were revealed. The results show that the surface and internal residual stresses of 20–100 mm thick plates have good symmetry on the paths perpendicular to the weld seam, and asymmetry only occurs in the weld seam and heat-affected zone where the stress fluctuates. On the paths perpendicular to the weld seam, the stress in the X direction transitions from the "M" shape distribution on the surface to the "Π" shape distribution inside for 20–40 mm thick plates, and the residual stress near the weld seam gradually changes from compressive to tensile; The distribution of stress in the X direction in the 80–100 mm thick plate has experienced the transition from "M" shape to "Π" shape to "M" shape, and the stress near the weld seam has experienced the transition from compressive to tensile to compressive. The stress change in the X direction of the 60 mm thick plate is between the above two cases. On the path of internal stress along the thickness, the maximum stress in the X direction is 310–400 MPa for 20–40 mm thick plates, which appears at about 1/2 plate thickness. The maximum stress in the X direction for 60–100 mm thick plates is 400–480 MPa, which appears at 0.2–0.3 times the thickness of the plate from the upper surface. The results could serve as a reference for welding residual stress analysis and guide optimization design of steel bridges made of thick steel plate.

Effect of welding layers and interlayer temperature on welding residual stress and deformation of Q345/316L dissimilar steel

Assessing the Residual Stresses in Dissimilar Welded Joint: Depth-Sensing Indentation Testing and Numerical Simulation

Effect of different welding parameters on residual stress and deformation of 20/0Cr18Ni9 dissimilar metal arc-welding joint

Modeling of welding residual stress in a dissimilar metal butt-welded joint between P92 ferritic steel and SUS304 austenitic stainless steel

Numerical simulation of S355JR-316L dissimilar metal welding

Numerical Simulation Analysis of Welding Residual Stress on Dissimilar Metal Welded Pipes

Regulation of welding residual stress in laser-welded AISI 304 steel-niobium joints using a Cu interlayer

Study on the Effect of Preheating Temperature on Residual Stress in Laser Arc Composite Welding of Dissimilar Aluminum Alloys

Effect of Thermophysical Parameters on the Hump Feature of Welding Residual Stress by Finite Element Analysis

FE analysis of residual stress and welding deformation of a low-alloy UHS quenched steel fillet joint

Numerical and experimental study on thermal-metallurgical-mechanical behavior of high-strength steel welded joint

Effect of Process Parameters on Welding Residual Stress of 316L Stainless Steel Pipe

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Numerical Study on Welding Residual Stress Distribution of Corrugated Steel Webs

Effect of Solid-State Phase Transformation and Transverse Restraint on Residual Stress Distribution in Laser–Arc Hybrid Welding Joint of Q345 Steel

Stress and distortion of the 10 mm thick plate EH40 and 316L different butt joints in 10 kW laser welding

Numerical simulation of residual stress before and after post-weld heat treatment in butt-welded pipes with dissimilar steel

Experimental research and numerical analysis of welding residual stress of butt welded joint of thick steel plate

Effects of Different Pre-Heating Welding Methods on the Temperature Field, Residual Stress and Deformation of a Q345C Steel Butt-Welded Joint

Numerical Simulation of Temperature Evolution, Solid Phase Transformation, and Residual Stress Distribution during Multi-Pass Welding Process of EH36 Marine Steel

Study of Residual Stress Evolution in SUS304/Q235 Bimetallic Clad Plate Butt-Welded Joints Considering Welding Sequence