Abstract:High undercooling rapid solidification process has a significant impact on the solidified microstructure and mechanical properties of materials. In this study, particles with a diameter range between 100 and 1100 μm of ternary Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys were prepared by a drop tube. The evolution process of particle-solidified microstructure with decreasing particle diameter was analyzed using XRD, SEM, and TEM. For Zr 50 Cu 40 Al 10 alloy, the solidified microstructure in the particle diameter ranges of 200–1100 μm is composed of an amorphous phase and a primary B2-ZrCu high-temperature metastable phase. As the particle diameter reduces, the retained crystalline phase in the solidified microstructure decreases progressively, and the dendrite grain length gradually becomes finer. When the particle diameter is reduced to below 200 μm, the crystalline phase has completely disappeared, and the solidified microstructure evolves into a completely amorphous structure. For Zr 49 Cu 46 Al 5 alloy, in the particle diameter range of 400–1100 μm, the solidified microstructure consists of primary B19'-ZrCu phase, a small amount of Cu 10 Zr 7 phase and Zr 14 Cu 51 phase. As the particle diameter reduces, a grain refinement phenomenon also occurs in the solidified microstructure and the dendritic morphology changes from equiaxed grain to rod-shaped dendrite. The amorphous phase appears when the particle diameter is lowered to 470 μm and solidified microstructure evolves into a completely amorphous structure as the particle diameter is reduced to 146 μm. The nanoindentation results show that the micromechanical properties of amorphous composite microstructures are superior to the single component composition of crystalline or amorphous phase for Zr 50 Cu 40 Al 10 and Zr 49 Cu 46 Al 5 alloys. The reinforcement effect on the amorphous phase is related to the content of the second crystalline phase. Moreover, under similar particle diameters, the mechanical properties of Zr 50 Cu 40 Al 10 particles are always better than those of Zr 49 Cu 46 Al 5 particles.

Crystal Structure and Colorimetric Behavior of Low Melting Point Ternary Alloy

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Crystal-to-amorphous phase transformation in ternary shape memory alloys

THERMO-MECHANICAL ASSESSMENT OF HIGH ENTROPHY (Fe-Ni-Cx (X=0.3-0.5), (Fe-Cr-Cx (X=0.3-0.5) TERNARY ALLOYS SYSTEM USING CALPHAD METHOD

Crystalline and amorphous microstructure evolution of Zr-Cu-Al ternary alloys solidified in drop tube

Phase Equilibria and Solidification of Ternary Sn–Bi–Ag Alloys

Phase Transformations and Mechanical Properties in In–Bi–Sn Alloys as a Result of Low-Temperature Storage

The Crystal Structure, Microhardness and Thermal Stability of the Ti26Al55Zn19 Alloy

Effect of Cu Particles on the Properties of Sn-Bi-Pb Low-Melting-Point Alloys

Low Temperature Preparation and Transport Properties of Ternary Pb—Bi —te Alloy.

Alloying Effect on the Microstructure and Property of Single Crystal Ni 3 Al Alloys

Thermodynamic study of the Ca-Cu-Zn ternary system with key experimental measurements

Thermo-mechanical behavior of hypoeutectic Ni-Y-Zr alloys

EFFECT OF Zr, Zn AND Cu ADDITIONS ON ELEVATED-TEMPERATURE MECHANICAL PROPERTIES OF AS-EXTRUDED Mg-3Sn-1Ca ALLOY

Effect of Alloying Elements, Solutionizing Time and Quenching Media on the Microstructure and Tensile Properties of 413-Based Alloys

Determination of the Parameters of Precipitates in Aged Mg – 8% Zn – 4% Al – 0.2% Cr – 0.5% Bi Alloy

Thermodynamic Properties and Phase Equilibria of Sn–Bi–Zn Ternary Alloys

A High Strength and High Conductivity Cu0.4Cr0.3Zr Alloy Prepared by Cryo-ECAP and Heat Treatment

The Effect of In Concentration and Temperature on Dissolution and Precipitation in Sn–Bi Alloys