Abstract:NiAl base eutectic alloy is an attractive material and promising to use in high temperature environment. However, the inadequate high temperature strength limits its application. In order to improve its strength, Zr was added in the Ti and Hf doped NiAl/Cr(Mo) base eutectic alloys and the effect of Zr addition on microstructure and mechanical properties of the eutectic alloy was investigated in this work. The results show that small addition of Zr can refine the NiAl/Cr(Mo) lamella inside the eutectic cell and optimize NiAl and Cr(Mo) phase morphology in the intercellular zone. Moreover, the Zr addition promotes the precipitation of bulk Heusler phase along eutectic cell boundary. With the increase of Zr addition, the eutectic cell of the alloys becomes fine, but the NiAl and Cr(Mo) phases in the intercellular zone become coarse and the Heusler phases exhibits semi-continuously distribution along the eutectic cell boundary. When the Zr content increases to 1% (atomic fraction), the NiAl and Cr(Mo) phases in eutectic cell and intercellular zone are all coarsened obviously. Additionally, coarse Cr-rich phases precipitate in the intercellular zone and Heusler phase forms the continuous network along eutectic cell boundary. The addition of Zr promotes the precipitation of coarse beta-NiAl and alpha-Cr phase in Cr(Mo) phase and NiAl phases, respectively. Moreover, the segregation of Heusler phase forming elements along the precipitate interface leads to the formation of a large number of interfacial dislocations. In addition, the addition of Zr results in the precipitation of fine Heusler particles in NiAl phase. It is shown that appropriate addition of Zr can improve the compression strength of Ni-33Al-28Cr-5.5Mo-1.0Ti-0.3Hf eutectic alloys significantly at room temperature and high temperature without reducing its compression plasticity, but more addition of Zr reduces the compressive plastic of the alloy inevitably.

Alloying Effect on the Microstructure and Property of Single Crystal Ni 3 Al Alloys

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Effect of microalloying additions on microstructural evolution and thermal stability in cast Al-Ni alloys

Microstructure-property relationship in Zr-alloyed Ni-rich NiTi alloys: Enhancements in high-temperature stability and superelasticity

Investigating the Influence of Al Contents on Microstructure and Mechanical Properties of Ni 3 Al Superalloy Fabricated by Twin Wire‐Based Direct Arc Energy Deposition

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Microstructure and mechanical properties of a novel polycrystalline Ni3Al-based intermetallic alloy

Ambient- and elevated temperature properties of Sc- and Zr-modified Al-6Ni alloys strengthened by Al3Ni microfibers and Al3(Sc, Zr) nanoprecipitates

The effect of chromium additions on the mechanical properties of Ni-25Al-27.5Fe-based intermetallic compounds

Improving the Microstructure and Mechanical Properties of Zr-Ti Alloy by Nickel Addition

Carbon addition and temperature dependent tensile deformation resistance and capacity of a low-cost 3rd-generation Ni-based single crystal superalloy

Microstructure and Mechanical Properties of Ni3Al and Ni3Al–1B Alloys Fabricated by SHS/HE

EFFECT OF Zr ADDITION ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF NiAl/Cr(Mo)BASE EUTECTIC ALLOY

Investigation on B, Cr Doped Ni3Al Alloy Prepared by Self-Propagation High-Temperature Synthesis and Hot Extrusion

Microstructures and Mechanical Properties of Cast Nb-Ti-Si-Zr Alloys

Effects of alloying elements on the super-lattice intrinsic stacking fault energy and ideal shear strength of Ni 3 Al crystals

Optimization of Ta Content of a Third Generation Ni3Al Base Single Crystal Superalloy

Thermo-mechanical behavior of hypoeutectic Ni-Y-Zr alloys

Improving mechanical properties of W-Ni 3 Al alloy through Zr element addition: Solid-solution and oxide particle strengthening

Microstructure and Mechanical Properties of Ni3Al Fabricated by Thermal Explosion and Hot Extrusion