Abstract:Laser powder bed fusion (LPBF) has emerged as an effective method for preparing complex structured silicon carbide (SiC) ceramics. However, the SiC components demonstrate low strength and high brittleness, which remain major challenges limiting its application. To overcome this limitation, short carbon fiber reinforced silicon carbide (C sf /SiC) composites are prepared by combining LPBF and phenolic resin binder impregnation (PRBI)-reactive melt infiltration (RMI), in which high char yield boron -and silicone -containing phenolic resin (BSiPF) impregnation is used to adjust the carbon density of green bodies and to reduce the pore size of green bodies. By optimizing the impregnation process, the carbon density can be brought close to the theoretical optimal value of 0.84 g/cm 3 , and the reduction of the pore size is conducive to the improvement of the reaction rate at the early stage of the reaction, which enhance the SiC phase content of C s f /SiC composites obtained by RMI. Meanwhile, the application of BSiPF results in a protective pyrolytic carbon (PyC) coating on the surface of C sf , which can reduce the erosion of C sf by molten Si during the RMI process, thus improving the fracture toughness of C s f /SiC composites. The final C s f /SiC composites exhibit the enhanced bulk density, bending strength and fracture toughness, reaching 2.90 +/- 0.01 g/cm 3 , 257 +/- 20 MPa, 3.52 +/- 0.15 MPa m 1/2 , respectively. This study provides a new strategy for effective impregnation technique for the additive manufacturing (AM) of high strength and high toughness SiC composites.

Preparation of carbon fiber-reinforced SiC ceramics by stereolithography and secondary silicon infiltration

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

The Preparation of SiC Ceramic Photosensitive Slurry for Rapid Stereolithography

Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Preparation of photosensitive SiO2/SiC ceramic slurry with high solid content for stereolithography

Stereolithography-based additive manufacturing of RB-SiC ceramics by a two-step sintering method

Application of SiO2-coated SiC Powder in Stereolithography and Sintering Densification of SiC Ceramic Composites

Fabrication of SiC Ceramic Architectures Using Stereolithography Combined with Precursor Infiltration and Pyrolysis

An efficient and low-cost liquid silicon infiltration method to prepare SiC-coated carbon short fiber for fiber protection of C<sub>f</sub>/SiC ceramic matrix composites

A stereolithographic diamond-mixed resin slurry for complex SiC ceramic structures

Additive Manufacturing Cf/SiC Composites with High Fiber Content by Stereolithography Combined with Precursor Infiltration and Pyrolysis

Fabrication of dense Cf/SiC ceramic matrix composites using 3D printing and PIP with short carbon fibre as a toughening material

Fabrication of High‐strength Porous SiC‐based Composites with Unidirectional Channels

High Strength and High Toughness Csf/SiC Composites Prepared by Laser Powder Bed Fusion/ Reactive Melt Infiltration with the Impregnation of Boron-and Silicone-Containing Phenolic Resin

A novel method for fabricating carbon fibre reinforced silicon carbide composites via 3d printing technology

An efficient and low-cost liquid silicon infiltration method to prepare SiC-coated carbon short fiber for fiber protection of Cf/SiC ceramic matrix composites

Microstructure Evolution and Performance Improvement of Silicon Carbide Ceramics via Impregnation Method

Preparation of carbon fiber reinforced silicon carbide porous ceramiccomposites with three dimensional network structure

Preparation of silicon carbide ceramic slurry for stereolithography based additive manufacturing

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration