Abstract:The paper considers the influence of the parameters of the plasma spraying process on the technological characteristics of multilayer coatings based on nickel-chromium, nickel-chromium-aluminum-yttrium materials, oxide ceramics, intended for operation at high temperature and additional dynamic loads. The design of plasma coatings during their application (with subsequent high-energy processing) under such conditions requires a comprehensive solution – both the use of high-quality powder ingredients and the optimization of technological parameters. The plasma process of applying powder materials has been improved to obtain the maximum values of their utilization factors. The technological characteristics that affect the properties of plasma coatings are optimized, namely: the flow rates of the plasma-forming and materials-transporting gases, the flow rate of supplied powder materials, the current and voltage of the electric arc of the plasma torch, the distance from the plasma torch nozzle exit to the substrate. The paper presents the results of studies of the structure of coatings, performed using scanning electron microscopy. Their analysis has made it possible to form general regularities obtained by the action of radiation of compression plasma flows on coatings formed by air plasma. The considered structures are created using the processes of melting, compaction and high-speed cooling of plasma coatings. The main optimization indicators are the maximum local compaction and spillage of the obtained compositions with the absence of defects and destruction from the impact of compression plasma flows. The main effect during the action of radiation of a compression plasma flow on previously formed coatings is thermal. It contributes heating of the near-surface layer. When the coating is exposed to radiation of compression plasma flows, a remelted layer of oxides with a thickness of about 12–15 μm is created, smoothing the relief of the formed surface and creating a network of cracks on the surface, diverging into the depth of the coating. The liquid-phase processes occurring in the molten phase of the near-surface layers after exposure to compression plasma radiation change the structure of the layers and contribute to the modification of their mechanical properties. By smoothing the surface, increasing the density of the surface crystallized layer and minimizing macro-defects – pores or macrocracks – the mechanical characteristics of the coatings increase.

Improving the Efficiency of Air Plasma Spraying of Titanium Nitride Powder

Influence of Plasma Arc Current and Gas Flow on the Structural and Tribological Properties of TiN Coatings Obtained by Plasma Spraying

Reactive nitrogen plasma spray coating of titanium nitride: plasma torch design and coating analysis

Plasma Spray Deposition Enhancement of Titanium Nitride Layer Using Nitrogen-Contained Plasma Irradiation of Titanium Substrate as a Pre-spraying Method

Surface modification of coatings based on Ni-Cr-Al by pulsed plasma treatment

Investigation on the Performance of TiN Coatings by Reactive Plasma Spraying Crystallization

Mechanical Properties Evaluation and Parametric Optimization of Atmospheric Plasma Spray NiTi Coating

The Crystallization Mechanism of Reactive Plasma Spraying

Multi-Layers Composite Plasma Coatings Based on Oxide Ceramics and M-Croll

The dependency of microstructure and properties of nanostructured coatings on plasma spray conditions

The Effect of Powder Preparation Method on the Corrosion and Mechanical Properties of TiN-based Coatings by Reactive Plasma Spraying

Effects of Treatment Process and Nano-Additives on the Microstructure and Properties of Al2O3-TiO2 Nanocomposite Powders Used for Plasma Spraying

Oxidation Behavior of Titanium Carbonitride Coating Deposited by Atmospheric Plasma Spray Synthesis

A Review and Progress of Multiphase Flows in Atmospheric and Low Pressure Plasma Spray Advanced Coating

Study of the properties of metal powder received by plasma

The Microstructure and Deposition Behavior of NiCr Alloy Coatings Using Laminar Plasma Spraying

Production of High-Power Nitrogen Sputtering Plasma for TiN Film Preparation

Deposition of Ti(C, N)-TiB2 Composite Coating by Reactive LPPS

The Effect of Plasma Spray Parameters on the Quality of Al-Ni Coatings

Investigation of Preparation and Properties of TiCN Coatings by Reactive Plasma Spraying

Synthesis of TiN/Ti3Al composite coatings on Ti6Al4V alloy by plasma spraying and laser nitriding