Abstract:Ti(C, N)-TiB2 composite coatings were deposited by means of reactive low pressure plasma spraying (LPPS) based on the technology of self-propagating high-temperature synthesis (SHS). The original powders were mixtures of Ti and B4C powders. The powders were mixed by ball mill and then spray-dried and at last sintered to be suitable for spraying. Two spraying distances were selected for LPPS. Scanning electron microscopy (SEM) was used to investigate the morphologies of powders for spraying and the microstructures of the coatings. The phase compositions of coatings were measured by X-ray diffraction (XRD). Spray-dried and sintered powders are denser and better bond than only spray-dried powders. The composite coating is composed of TiB2, TiC0.3N0.7, TiN0.3, Ti4N3-x and impurity phase of Ti5Si3 with 300 mm spraying distance. Partly unreacted B4C powders remained in the coating for 240 mm spraying distance, which may be inadequate reaction. No titanium oxide was detected in the composite coating for the relative high vacuum degree of LPPS. The anti-corrosion property of LPPS sprayed Ti(C, N)-TiB2 composite coating with 300 mm spraying distance in electrolytic solution is superior to that of 240 mm spraying distance. Microhardness of Ti(C, N)-TiB2 composite coating is relatively low due to the unconsolidated structure of the coating. The solving methods to improve property of composite coating are finally put forward in the paper.

Investigation of Preparation and Properties of TiCN Coatings by Reactive Plasma Spraying

Investigation on the Performance of TiN Coatings by Reactive Plasma Spraying Crystallization

In-situ TiC-Ti5Si3-SiC composite coatings prepared by plasma spraying

The crystallization behaviours of reactive-plasma-sprayed TiCN coatings with different Ti/graphite powder ratios

Deposition of Ti(C, N)-TiB2 Composite Coating by Reactive LPPS

The Crystallization Mechanism of Reactive Plasma Spraying

Oxidation Behavior of Titanium Carbonitride Coating Deposited by Atmospheric Plasma Spray Synthesis

Preparation and Properties of Composite Nanoceramic NiCrBSi-TiO2/WC(Co) Coatings

Nanostructured TiN Coating Prepared by Reactive Plasma Spraying in Atmosphere

Influence of nitridation on the microstructure and corrosion behavior of reactive plasma sprayed TiCN coatings

The Effect of Powder Preparation Method on the Corrosion and Mechanical Properties of TiN-based Coatings by Reactive Plasma Spraying

TiC-TiSi2-Al2O3 composite coatings prepared by spray drying, heat treatment and plasma spraying

Deposition and properties of plasma sprayed NiCrCoMo–TiC composite coatings

Fabrication of plasma-sprayed TiC-Ti5Si3-Ti3SiC2 composite coatings from the annealed Ti/SiC powders

TEM characterization and reaction mechanism of composite coating fabricated by plasma spraying Nb–SiC composite powder

Plasma sprayed TiC–Ti5Si3–Ti3SiC2 composite coatings from Ti–SiC-graphite powders with different SiC particle size

Tribological Characteristics of TiN and TiCN Hard Coatings Prepared by Pulsed D.C. Plasma Enhanced Chemical Vapour Deposition

Preparation and Microstructure Characteristics of Super-Hard Nanocomposite Ti-Si-C-N Coatings Deposited by Pulsed Dc Pcvd

Cold-sprayed Ni-cBN Coating and its Friction and Wear Properties

Microstructure and properties of TiC–Fe36Ni cermet coatings by reactive plasma spraying using sucrose as carbonaceous precursor

EFFECT OF COMPOSITION AND MECHANICAL PREPARATION METHOD OF A COMPOSITE TiC–Ni MIXTURE ON TITANIUM CARBIDE CONTENT IN COATINGS FORMED BY COLD SPRAYING