Abstract:TiAl intermetallic compounds, as a new kind of high-performance light-weight structural material, are widely applied in many fields. Titanium carbide (TiC) as the reinforcing phase could improve the mechanical properties, wear resistance, and heat-resistance stability of TiAl intermetallic compounds. Ti(Al, C) mixture powders were deposited by cold spraying at gas temperature of 250 °C, 450 °C, and 550 °C. Then, Ti(Al, C) coatings were annealed at temperatures of 650 °C for different times and following holding at 1100 °C for 3 h. The microstructure, microhardness, fracture toughness, and abrasive wear of Ti-Al composite coatings were investigated. The research results were that the particle size of mixture powders decreased as the ball milling time prolonging. Ti(Al) solid solution appeared in the mixture powders as the milling time increased to 30 h. The average porosity of the coating sprayed at 550 °C was the lowest (0.85%). The as-sprayed coatings exhibited the same phase compositions with the mixture powders. The coating sprayed at gas temperature of 550 °C has the highest microhardness and the lowest weight loss. Ti-Al intermetallic was in-situ synthesized after annealing at 650 °C. The average porosity of the annealed coating (sprayed at 450 °C) was the lowest. The content of Ti-Al intermetallic compounds of the annealed coating sprayed at 450 °C is the highest. The X-ray diffraction (XRD) analysis results are consistent with the EDS analysis of the annealed coatings after annealing at 650 °C. Ti-Al intermetallic compounds were almost completely formed in the three kinds of the coatings after annealing at 650 °C for 20 h and following holding at 1100 °C for 3 h. TiAl and TiAl3 intermetallic phases were in-situ synthesized in the coatings based on the energy dispersive spectroscopy (EDS) and XRD analysis. TiC was also in situ synthesized in the coatings as the annealing temperature increased to 1100 °C. The annealed coating (sprayed at 450 °C) has the highest microhardness, fracture toughness, and wear resistance properties after annealing at 1100 °C for 3 h.

In-situ TiC-Ti5Si3-SiC composite coatings prepared by plasma spraying

TiC-TiSi2-Al2O3 composite coatings prepared by spray drying, heat treatment and plasma spraying

Plasma sprayed TiC–Ti5Si3–Ti3SiC2 composite coatings from Ti–SiC-graphite powders with different SiC particle size

Fabrication of plasma-sprayed TiC-Ti5Si3-Ti3SiC2 composite coatings from the annealed Ti/SiC powders

Microstructure evolution and mechanical properties of reactive plasma sprayed Ti3SiC2–Ti5Si3–TiC composite coatings

Microstructure and properties of Cr7C3-CrSi2 composite coatings prepared by plasma spraying

Microstructure and tribological properties of Al-30Si-5Cu composite coating reinforced with ceramic phases synthesized in situ by plasma spraying

Effect of Si content on the microstructure and properties of Ti–Si–C composite coatings prepared by reactive plasma spraying

Superior Ablation Resistance of Plasma Sprayed SiC Based Coating by Structural Optimized Powders

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Microstructure and properties of in-situ ZrB2-ZrC composite coatings by plasma spraying

Investigation of Preparation and Properties of TiCN Coatings by Reactive Plasma Spraying

TEM characterization and reaction mechanism of composite coating fabricated by plasma spraying Nb–SiC composite powder

Microstructure, Microhardness, Fracture Toughness, and Abrasive Wear of In-Situ Synthesized TiC/Ti-Al Composite Coatings by Cold Spraying Combined with Heat Treatment

Microstructure and properties of plasma sprayed copper-matrix composite coatings with Ti3SiC2 addition

TEM Exploration of In-Situ Nanostructured Composite Coating Fabricated by Plasma Spraying 8Ysz-Al-sic Composite Powder

Preparation and properties of reactive plasma sprayed TiC–Ti5Si3–Ti3SiC2/Al coatings from Ti–Si–C–Al mixed powders

Microstructure and properties of Al2O3–ZrO2–TiO2 composite coatings prepared by plasma spraying

Influence of graphite additive on microstructure and mechanical characteristics of plasma sprayed TiB2–TiC composite coating

Properties of Reactive Plasma Sprayed Tib2-Tic0.3n0.7 Based Composite Coatings with Cr Addition and Laser Surface Treatment

Deposition and properties of plasma sprayed NiCrCoMo–TiC composite coatings