Abstract:AISI 52100 steel has been widely used in the mechanical industry due to its excellent mechanical properties and high availability. In some cases, an ultra-smooth surface of AISI 52100 steel is needed and is even indispensable for the satisfactory performance of devices. In this paper, chemical mechanical polishing technique was employed to prepare the ultra-smooth surface of AISI 52100 steel. Colloidal silica was used as the abrasive. The effects of pH, complexing agent such as glycine, H2O2 and benzotriazole (BTA) on the polishing performance were studied. It is revealed that, with the increase of pH, the static etching rate (SER) and the material removal rate (MRR) are both gradually reduced, and the post-CMP surface roughness I?, decreases. This is attributed to the fact that compact and passive iron oxides, especially Fe(III) oxides, gradually form on the top surface. At pH 4.00, in the presence of glycine, and with the increase of the H2O2 concentration, the SER is further suppressed, and the surface roughness R-a gradually decreases; the MRR initially dramatically increases due to the fact that, with the addition of small amount of H2O2, the porous iron oxide layer with relatively low mechanical strength can be rapidly formed on the surface. Moreover, glycine intensifies the chemical dissolution by chelating iron ions, especially Fe(II) ions, and thereby the mechanical strength of the oxide layer further weakens. Then, after reaching the peak value, the MRR gradually decreases when the H2O2 concentration further increases since the compactness of the oxide layer gradually increases. With the increase of the BTA concentration, the MRR is gradually suppressed and the surface roughness R-a decreases due to the formation of Fe-BTA passivating film on the top surface. Finally, a two-step polishing process was developed. The polishing results show that, within 20 min, a rough surface of AISI 52100 steel with the R-a value of 188 nm can be polished into an ultra-smooth surface with the R-a value of 1.8 nm. (C) 2015 Elsevier B.V. All rights reserved.

A New Chemical-Mechanical Polishing Method Based On Colloids Silica and MgO Was Developed For Polishing Y3Al5O12 Material

Trivalent lanthanum and ytterbium doped meso-silica/ceria abrasive systems toward chemical mechanical polishing (CMP) and ultraviolet irradiation-assisted photochemical mechanical polishing (PCMP)

Research on Chemical Mechanical Polishing Technology for Zirconium-Based Amorphous Alloys

Achieving Ultralow Surface Roughness and High Material Removal Rate in Fused Silica Via a Novel Acid SiO2 Slurry and Its Chemical-Mechanical Polishing Mechanism

CHEMICAL MECHANICAL POLISHING AND ITS MECHANISM ON YTTERBIUM-DOPED MIXED SESQUIOXIDES (Yb:Lusco3)

Non-spherical abrasives with ordered mesoporous structures for chemical mechanical polishing

Investigation of Chemical Mechanical Polishing Slurry of magnesium alloy

Polishing Mechanism of CMP 4H-SiC Crystal Substrate (0001) Si Surface Based on an Alumina (Al2O3) Abrasive

Angstrom surface with high material removal rate for quartz glass induced by silk dissolved novel green chemical mechanical polishing

Surface Characteristics of Polished YAG Laser Crystal

Novel green chemical mechanical polishing for an aluminum alloy and mechanisms interpreted by molecular dynamics simulations and measurements

Chemical Mechanical Polishing of Steel Substrate Using Colloidal Silica-Based Slurries

High-performance chemical mechanical polishing slurry for aluminum alloy using hybrid abrasives of zirconium phosphate and alumina

In-Situ Laser Polishing Additive Manufactured AlSi10Mg: Effect of Laser Polishing Strategy on Surface Morphology, Roughness and Microhardness

RE (la, Nd and Yb) Doped CeO2 Abrasive Particles for Chemical Mechanical Polishing of Dielectric Materials: Experimental and Computational Analysis

Development of core–shell SiO 2 @A-TiO 2 abrasives and novel photocatalytic chemical machinal polishing for atomic surface of fused silica

Sulfuric Acid Etching for Surface Modification and Improved Polishing of Magnesium Aluminate Spinel

Femtosecond laser surface modification of magnesium aluminate spinel and its effect on polishing

Improving Surface Electrochemical Polishing Quality of Additive Manufactured AlSi10Mg by Reconstituting the Si Phase

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

XPS, UV–vis Spectroscopy and AFM Studies on Removal Mechanisms of Si-face SiC Wafer Chemical Mechanical Polishing (CMP)