Abstract:Laser Powder Bed Fusion (L-PBF) provides a larger design freedom than conventional manufacturing techniques. Surface post-processing is widely investigated to improve the roughness of as built L-PBF parts by reducing powder sintered to the surface and the staircase effect, but it becomes even more important to guarantee a smooth surface if support structures are included for tilted overhanging structures. This study focuses on L-PBF AlSi10Mg samples with a building angle of 30° with respect to the baseplate. This building angle inevitably requires support structures. The study investigates if a hybrid surface treatment combining chemical and electrochemical polishing, called Hirtisation®, removes the support structure and to what extent it improves the surface roughness of samples with a 30° building angle. Currently, the results of surface treatments are mostly reported on vertically built samples while down-facing areas of samples with a lower building angle are typically the roughest areas of the samples causing crack initiation in fatigue. Roughness, defect population, residual stresses, microstructure, fatigue, and tensile properties are studied to investigate correlations with the physical effect of Hirtisation. A porous zone is observed in the down-facing area close to the support structures of as built samples. Hirtisation removed successfully the support and the porous area. In the down-facing roughest area, the average values of the average roughness, mean roughness depth and deepest valley depth are reduced by respectively 56,5%, 58,7% and 51,5% by Hirtisation compared to the as built state. The deepest valley measured reduced from 155,5 μm to 74,4 μm. Hirtisation combined with annealing increased the fatigue resistance at a stress amplitude of 120 MPa with a factor 3,1 compared to the as built state and with a factor 2,7 compared to the annealing state. The improved fatigue resistance is linked to halving the deepest valley depth as well as a change in the residual stress at the outer surface from tensile stresses after annealing to a small compressive stress after Hirtisation which counteracts the tensile load in fatigue. Hence, Hirtisation reduces roughness, inverses a tensile residual stress at the outer surface to a small compressive residual stress. In addition, the chemical-electrochemical process allows to access areas which are impossible to post-process with e.g. sandblasting or vibratory polishing. These conclusions make Hirtisation interesting for further investigations for future applications, however the deepest valley depth could be reduced more by increasing the material removal in the process to improve the fatigue life more.

Improving Surface Electrochemical Polishing Quality of Additive Manufactured AlSi10Mg by Reconstituting the Si Phase

High-quality surface smoothening of laser powder bed fusion additive manufacturing AlSi10Mg via intermittent electrochemical polishing

A comparison study of the electrochemical polishing of laser powder bed fusion HR-2 stainless steel and AlSi10Mg

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Investigation on pulsed electrolytically polished AlSi10Mg alloy processed via selective laser melting technique

In-Situ Laser Polishing Additive Manufactured AlSi10Mg: Effect of Laser Polishing Strategy on Surface Morphology, Roughness and Microhardness

Innovative Post-Processing for Complex Geometries and Inner Parts of 3D-Printed AlSi10Mg Devices

Investigation on surface integrity of electron beam melted Ti-6Al-4 V by precision grinding and electropolishing

Application of electrochemical polishing in surface treatment of additively manufactured structures: A review

Surface quality improvement for 316L additive manufactured prototype based on magnetorheological polishing

Surface Characteristics Enhancement and Morphology Evolution of Selective-Laser-melting (SLM) Fabricated Stainless Steel 316L by Laser Polishing

Optimisation of the laser polishing for laser-powder bed fusion and electron beam-powder bed fusion Ti6Al4V surfaces

Quantitative-regulated Material Removal Rate in Solid Dielectric Electrochemical Polishing (QRR-SDEP) for Smoothing High Roughness Surface of Additively Manufactured 316L Stainless Steel Components

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Surface Finishing of 3D-Printed Ti-6Al-4 V Alloy by Electrolyte Plasma Polishing: Process Optimization and Microstructure

Investigation of Laser Polishing of Four Selective Laser Melting Alloy Samples

Solid Dielectric Electrochemical Polishing of 3D-Printed Parts: Performance and Mechanisms

Improvement of mechanical properties and corrosion resistance of SLM-AlSi10Mg alloy by an eco-friendly electric pulse treatment

Effect of Hirtisation treatment on surface quality and mechanical properties of AlSi10Mg samples produced by laser powder bed fusion

Surface Modification and Mechanical Properties of Laser Powder Bed Fusion Inconel 718 after Magnetic-Assisted Laser Polishing

Electrorheological fluid–assisted ultrasonic polishing for IN625 additively manufactured surfaces