Abstract:Laser Powder Bed Fusion (L-PBF) provides a larger design freedom than conventional manufacturing techniques. Surface post-processing is widely investigated to improve the roughness of as built L-PBF parts by reducing powder sintered to the surface and the staircase effect, but it becomes even more important to guarantee a smooth surface if support structures are included for tilted overhanging structures. This study focuses on L-PBF AlSi10Mg samples with a building angle of 30° with respect to the baseplate. This building angle inevitably requires support structures. The study investigates if a hybrid surface treatment combining chemical and electrochemical polishing, called Hirtisation®, removes the support structure and to what extent it improves the surface roughness of samples with a 30° building angle. Currently, the results of surface treatments are mostly reported on vertically built samples while down-facing areas of samples with a lower building angle are typically the roughest areas of the samples causing crack initiation in fatigue. Roughness, defect population, residual stresses, microstructure, fatigue, and tensile properties are studied to investigate correlations with the physical effect of Hirtisation. A porous zone is observed in the down-facing area close to the support structures of as built samples. Hirtisation removed successfully the support and the porous area. In the down-facing roughest area, the average values of the average roughness, mean roughness depth and deepest valley depth are reduced by respectively 56,5%, 58,7% and 51,5% by Hirtisation compared to the as built state. The deepest valley measured reduced from 155,5 μm to 74,4 μm. Hirtisation combined with annealing increased the fatigue resistance at a stress amplitude of 120 MPa with a factor 3,1 compared to the as built state and with a factor 2,7 compared to the annealing state. The improved fatigue resistance is linked to halving the deepest valley depth as well as a change in the residual stress at the outer surface from tensile stresses after annealing to a small compressive stress after Hirtisation which counteracts the tensile load in fatigue. Hence, Hirtisation reduces roughness, inverses a tensile residual stress at the outer surface to a small compressive residual stress. In addition, the chemical-electrochemical process allows to access areas which are impossible to post-process with e.g. sandblasting or vibratory polishing. These conclusions make Hirtisation interesting for further investigations for future applications, however the deepest valley depth could be reduced more by increasing the material removal in the process to improve the fatigue life more.

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Microstructural analysis of the influences of platform preheating and post-build heat treatment on mechanical properties of laser powder bed fusion manufactured AlSi10Mg alloy

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

Influence of Contour Scan Variation on Surface, Bulk and Mechanical Properties of LPBF-Processed AlSi7Mg0.6

The Influence of Post-Treatment on Micropore Evolution and Mechanical Performance in AlSi10Mg Alloy Manufactured by Laser Powder Bed Fusion

Effect of heat treatments on microstructure and mechanical properties of AlSi10Mg alloys fabricated by laser powder bed fusion

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects

Achieving High Strength-Ductility Combination of Al-Mn-Mg-Sc-Zr Alloy Subjected by Laser Powder Bed Fusion and Suitable Post Heat Treatment

Role of Direct Aging and Solution Treatment on Hardness, Microstructure and Residual Stress of the A357 (AlSi7Mg0.6) Alloy Produced by Powder Bed Fusion

Effect of Hirtisation treatment on surface quality and mechanical properties of AlSi10Mg samples produced by laser powder bed fusion

Experimental and Statistical Analysis of the Effect of Heat Treatment on Surface Roughness and Mechanical Properties of Thin-Walled Samples Obtained by Selective Laser Melting from the Material AlSi10Mg

High-Temperature Mechanical Properties of Stress-Relieved AlSi10Mg Produced via Laser Powder Bed Fusion Additive Manufacturing

On the Role of Microstructure and Defects in the Room and High-Temperature Tensile Behavior of the PBF-LB A357 (AlSi7Mg) Alloy in As-Built and Peak-Aged Conditions

Improving the mechanical properties of Al-5Si-1Cu-Mg aluminum alloy produced by laser additive manufacturing with post-process heat treatments

The effect of the iso‐thermal heat treatment on the microstructure and properties of powder bed fusion‐laser beam AlSi10Mg alloy

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

Process Optimization and Mechanical Property Evolution of AlSiMg0.75 by Selective Laser Melting

In-situ mechanical and microstructural characterization of miniaturized Al-Mg-Sc-Zr and AlSi10Mg specimens processed by laser powder-bed fusion (PBF-LB)

Fretting wear behavior on LPBF processed AlSi10Mg alloy for different heat treatment conditions

Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment