Abstract:The most important advantage of additive manufacturing by laser powder bed fusion (PBF-LB) technique is the ability to produce geometrically complex parts, but the problem is their rough surfaces, often difficult or inaccessible to finish by machining. Therefore, research to improve the reproducibility of the mechanical behavior of parts manufactured from aluminum alloy powders with as-built surfaces is of vital importance for the aerospace and automotive industries. Since local notches occurring on rough surfaces after the PBF-LB process are unavoidable, the way to solve this problem is to obtain as-built surfaces of the highest possible quality and to adapt a post-process heat treatment that increases the ductility and fracture toughness of the material. To this end, the present work focused on the study of the mechanical performance of AlSi7Mg0.6 samples with a rough as-built surface in the as-built state and after several variants of post-process heat treatment, combined with a detailed analysis of the microstructures corresponding to these states. Tensile samples built on a platform preheated to 100 °C, achieved a relative density of 99.85%, satisfactory surface quality, a relatively low level of residual stress and moderate crystallographic texture. Despite the rough surface, the samples under the as-built condition and after different variants of heat treatment (direct aging (DA), stress relieving (SR), and solution annealing followed by artificial aging (T6)), achieved tensile properties comparable to those reported in the literature for PBF-LB samples with machined surfaces. The resulting combinations of tensile properties of PBF-LB samples after different heat treatment variants were evaluated using the quality index (QI) commonly used to assess the quality of heat-treated Al-Si-Mg castings. It was found that the proposed T6 treatment provides the best combination of strength properties and ductility, compared to those obtained after both DA and SR, as well as after T6 treatment of high-quality castings, from the point of view of reducing the sensitivity of AlSi7Mg0.6 alloy to surface roughness.

Role of Direct Aging and Solution Treatment on Hardness, Microstructure and Residual Stress of the A357 (AlSi7Mg0.6) Alloy Produced by Powder Bed Fusion

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects

The impact of heat treatment on microstructure, residual stress, and mechanical behavior of laser powder bed fusion additively manufactured Ti–6Al–2Sn–4Zr–2Mo alloy

A357 Alloy by LPBF for Industry Applications

On the Role of Microstructure and Defects in the Room and High-Temperature Tensile Behavior of the PBF-LB A357 (AlSi7Mg) Alloy in As-Built and Peak-Aged Conditions

Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting

Effect of Solution Aging Treatment on High and Very High Cycle Fatigue Properties of Nickel-Based Alloy Fabricated by Laser Powder Bed Fusion at 25 °C and 650 °C

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Microstructural, Mechanical, and Tribological Evolution under Different Heat Treatment Conditions of Inconel 625 Alloy Fabricated by Selective Laser Melting

Influence of aging treatments on 17–4 PH stainless steel parts realized using material extrusion additive manufacturing technologies

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Al-7Si-0.7Mg-2.5Fe Processed by Laser Powder Bed Fusion

The influence of post-thermal treatments on microstructure and mechanical properties in A20X alloy fabricated through powder bed fusion

Influence of powder layer thickness on microstructure and T5 heat treatability of F357 alloy fabricated by laser powder bed fusion process

A new high-throughput method using additive manufacturing for alloy design and heat treatment optimization

Design and Optimization of the Local Laser Treatment to Improve the Formability of Age Hardenable Aluminium Alloys

Achieving Balanced Mechanical Properties in Laser Powder Bed Fusion Processed Inconel 718 Superalloy Through a Simplified Heat Treatment Process

Effects of Heat Treatments on the Microstructure and Tensile Properties of IN738 Superalloy with High Carbon Content Fabricated Via Laser Powder Bed Fusion

Natural and artificial aging behaviour of Al-Cu-Mg-Ag-Ti-B (A205) alloy processed by laser powder bed fusion: Strengthening mechanisms and failure analysis

Heat Treatment Optimization of 2219 Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

The Influence of Post-Treatment on Micropore Evolution and Mechanical Performance in AlSi10Mg Alloy Manufactured by Laser Powder Bed Fusion

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment