Abstract:The newly designed alloy compositions for selective laser melting (SLM) have aroused great interest. In this study, zirconium modified Al-Cu-Mg alloys were fabricated by SLM. Results show that crack-free samples with relative density of nearly 100% were obtained by optimizing the processing parameters. With the increase of scanning speed, the relative density decreases due to insufficient energy input. In addition, the microstructure transforms from homogeneous to bio-modal, the reason is the unstable flows caused by the high scanning speed. The small hatching space will provide more energy input and preheat, leading to the coarse surface. Introduction Additive Manufacturing (AM) processes enable to fabricate parts with very complex shape[1]. Selective laser melting (SLM), one of the preferred AM techniques, has recently gained considerable attention due to high manufacturing flexibility, nearnet-shape production and efficient use of raw material[2, 3]. Al-Cu-Mg alloy has become an attractive material due to the low density, high fracture toughness and fatigue strength[4, 5]. Nowadays, processing high strength aluminum alloys by SLM is confronted with great difficulties because of its poor flowability, high reflectivity, high thermal conductivity, large solidification range and hot cracking susceptibility[6]. Therefore, the biggest stumbling block to the application of high strength aluminum in SLM is the hot crack. To expand the scope of aluminum alloys suiting for SLM, new high strength aluminum alloys are urgent to be investigated. Recently, scandium (Sc), zirconium (Zr), titanium (Ti) and vanadium (V) have been proved as the effective microalloying element for aluminum alloys to improve the weldability and mechanical properties[7-9]. Nowadays, the addition of microalloying element has been applied to SLM aluminum alloys to improve their formability. The microstructural evolution, densification, properties and heat treatment of Al-Mg-Sc-Zr fabricated by SLM have been investigated[10-13]. Zhang H et al.[14] have found that the Zr modified Al-Cu-Mg parts with ultrafine grain exhibits better mechanical properties and broader processing window. However, the effect of processing parameters on the Zr modified Al-Cu-Mg alloy has not been studied. 1246 Solid Freeform Fabrication 2018: Proceedings of the 29th Annual International Solid Freeform Fabrication Symposium – An Additive Manufacturing Conference Reviewed Paper

Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Effect of Selective Laser Melting Process Parameters on the Quality of Al Alloy Parts: Powder Characterization, Density, Surface Roughness, and Dimensional Accuracy

Effect of Processing Parameters on the Densification of an Additively Manufactured 2024 Al Alloy

The Effect of Selective Laser Melting Process Parameters on the Microstructure and Mechanical Properties of Al6061 and AlSi10Mg Alloys

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Role of Direct Aging and Solution Treatment on Hardness, Microstructure and Residual Stress of the A357 (AlSi7Mg0.6) Alloy Produced by Powder Bed Fusion

Experimental Investigation on Selective Laser Melting Behaviour and Processing Windows of in Situ Reacted Al/Fe2o3 Powder Mixture

Influence Mechanism of Process Parameters on Relative Density, Microstructure, and Mechanical Properties of Low Sc-Content Al-Mg-Sc-Zr Alloy Fabricated by Selective Laser Melting

Selective laser melting of Al 6061 alloy : Processing , microstructure , and mechanical properties

Effect of selective laser melting (SLM) process parameters on microstructure and mechanical properties of 316L austenitic stainless steel

Effect of process parameters on microstructures and properties of Al-42Si alloy fabricated by selective laser melting

Selective Laser Melting of Aluminum and Its Alloys

Selective Laser Melting of High Strength Al–Cu–Mg Alloys: Processing, Microstructure and Mechanical Properties

The effect of processing parameter on zirconium modified Al-Cu-Mg alloys fabricated by selective laser melting

Fabrication and Heat Treatment of High Strength Al-Cu-Mg Alloy Processed Using Selective Laser Melting

On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties

Microstructure–Texture–Mechanical Property Relationship in Alloys Produced by Additive Manufacturing Following Selective Laser Melting (SLM) Technique

Influence of Abrasive Materials in Fluidised Bed Machining of AlSi10Mg Parts Made through Selective Laser Melting Technology

Formability and hardness studies of selective laser melting of GH4169 Ni-based alloy powders

Effect of process parameter optimization on morphology and mechanical properties of Ti6Al4V alloy produced by selective laser melting